Abstract:Although <math>{101¯2}</math> twinning behavior has been extensively studied, it has rarely been investigated under biaxial tension. In the present research, the mechanical response and <math>{101¯2}</math> twinning behavior of a Mg AZ31 sheet under biaxial tension with various stress ratios (<math>σND:σTD</math>) along the normal direction (ND) and transverse direction (TD) were systematically studied. The results indicate that the yield stress along the ND is nearly independent of <math>σND:σTD</math>. Schmid law applied to <math>{101¯2}</math> twinning under biaxial tension yields better efficiency than that for uniaxial tension, and a higher efficiency is observed with a larger stress ratio along the TD; the fraction of experimentally observed twin variants with Schmid factors (SFs) of ranks 1 and 2 is approximately 45% for uniaxial tension, whereas it is approximately 68% for <math>σND:σTD=2:1</math> and approximately 88% for <math>σND:σTD=1:2</math>. This result contradicts with the previously reported result that Schmid law is more efficient for uniaxial stress states than under multiaxial stress conditions. It is found that biaxial tension will increase the difference in SF for the six twin variants and make Schmid law more efficient. Twin variant selection and volume fraction are highly dependent on <math>σND:σTD</math>. For uniaxial tension, the activities for the six variants are similar, and the (0002) poles of the twins are distributed evenly on a circle approximately 80°–90° away from the ND. In contrast, the variants <math>(01¯12)[011¯1]</math> and <math>(011¯2)[01¯11]</math> are more favorable under biaxial tension, and more (0002) poles of the twins concentrate around the rolling direction with a higher ratio of <math>σTD</math>. At a similar strain level, the twin fraction under biaxial tension is often different from that under uniaxial tension, and this difference varies with <math>σND:σTD</math>. This mechanism is associated with a stress-ratio-mediated detwinning behavior under biaxial tension. The findings in the present study provide a new and significant understanding of the twinning behavior of Mg alloys.

{11(2)Over-Bar1}-{10(1)Over-Bar2} Double Twinning In A Zircaloy-4 Alloy During Rolling At Ambient Temperature

The Effect Of {10(1)Over-Bar1}-{10(1)Over-Bar2} Double Twinning On The Microstructure, Texture And Mechanical Properties Of Az31 Magnesium Alloy Sheet During Rolling Deformation

Twinning Behavior of a Strongly Basal Textured AZ31 Mg Alloy During Warm Rolling

The effect of {1011}-{1012} double twinning on the microstructure, texture and mechanical properties of AZ31 magnesium alloy sheet during rolling deformation

The effect of {10¯11}–{10¯12} double twinning on the microstructure, texture and mechanical properties of az31 magnesium alloy sheet during rolling deformation

Promoting hybrid twins structure to reduce yield asymmetry of rolled AZ31 plates by combining side-rolling and torsion

Towards understanding double extension twinning behaviors in magnesium alloy during uniaxial tension deformation

{332}<113> and {112}<111> Twin Variant Activation during Cold-Rolling of a Ti-Nb-Zr-Ta-Sn-Fe Alloy

{ 10 1 ̄ 2 } twinning behavior under biaxial tension of Mg–3Al–1Zn plate

Quantitative investigation on the {10–12} twinning-detwinning behavior and twinning transfer of an extruded Mg-2.8Y sheet during compression-tension loading via quasi-in-situ EBSD observation

An Investigation of Slip and Twinning Behavior of a Zirconium Alloy During Plastic Deformation Based on In-Situ SEM-EBSD

An Atomic-Level Mechanism of Annealing Twinning in Copper Observed by Molecular Dynamics Simulation

INFLUENCE OF ROLLING TEMPERATURE ON THE {1011}-{1012} TWINNING IN ROLLED AZ31 MAGNESIUM ALLOY SHEETS

Texture and Twinning Evolution of Cold-Rolled Industrial Pure Zirconium

Influence of Deformation Twins on Mechanical Properties and Β Precipitation of Large-Cross-Section (290 Mm × 230 Mm) AZ80 Bar Fabricated by “Multi-Direction Forging + Extrusion + Cold Compression” Technique

Microtwinning mechanism revealed by its orientation dependence and tension-compression asymmetry in γ′ precipitate-strengthened Ni-based superalloys

EBSD Analysis and Theoretical Prediction of Twin Orientations During Compression in Mg-3Al-1Zn

Novel deformation twinning system in a cold rolled high-strength metastable- Ti-5Al-5V-5Mo-3Cr-0.5Fe alloy

Effect of Local Stresses of Primary Twinning on Double Twinning, Twin Intersection and Their Competition

An alternative formation mechanism of {332}BCC twinning in metastable body-centered-cubic high entropy alloy

A new mechanism of lamellar kinking produced by α twins