Abstract:The performance of high frequency, single-element transducers depends greatly on the mechanical and electrical properties of the piezoelectric materials used. This study compares the design and performance of transducers incorporating different materials. The materials investigated include 1-3 lead zirconate titanate (PZT) fiber composite, lead titanate (PbTiO3) ceramic, poly(vinylidene fluoride) (PVDF) film, and lithium niobate (LiNbO3) single crystal. All transducers were constructed with a 3-mm aperture size and an f-number between 2 and 3. Backing and matching materials were selected based on design goals and fabrication limitations. A simplified coaxial cable tuning method was employed to match the transducer impedance to 50 ohms for the PZT fiber composite and PbTiO3 ceramic transducers. Transducers were tested for two-way loss and -6 dB bandwidth using the pulse/echo response from a flat quartz target. Two-way loss varied from 21 to 46 dB, and bandwidths measured were in the range from 47 to 118%. In vitro ultrasonic backscatter microscope (UBM) images of an excised human eye were obtained for each device and used to compare imaging performance. Both press-focusing and application of a lens proved to be useful beam focusing methods for high frequency. Under equal gain schemes, the LiNbO3 and PbTiO3 transducers provided better image contrast than the other materials.

Characterization Of High-Frequency Ultrasound Transducers Made Of Alternating Current Poled Pb(Mg1/3nb2/3)O3-Xpbtio3 Single Crystals

Characterization of High-frequency Ultrasound Transducers Made of Alternating Current Poled $pb (\Text{mg}_{1/3}\text{nb}_{2/3})\mathrm{o}_{3}-X\text{pbtio}_{3}$ Single Crystals

Optimizing the Piezoelectric Vibration of Pb(Mg1/3Nb2/3)O3-0.25PbTiO3 Single Crystal by Alternating Current Polarization for Ultrasonic Transducer

Effect Of Low-Frequency Alternating Current Poling On 5-Mm-Thick 0.7pb(Mg1/3nb2/3)O-3-0.3pbtio(3) Single Crystals

Design and Fabrication of PIN-PMN-PT Single-Crystal High-Frequency Ultrasound Transducers.

Effect of low-frequency alternating current poling on 5-mm-thick 0.7Pb(Mg<sub>1/3</sub>Nb<sub>2/3</sub>)O<sub>3</sub>-0.3PbTiO<sub>3</sub> single crystals

High-frequency PIN–PMN–PT Single Crystal Ultrasonic Transducer for Imaging Applications

Alternating Current Poling on Sliver-Mode Rhombohedral Pb(Mg1/3nb2/3)O3-Pbtio3 Single Crystals

Pin-Pmn-Pt Single Crystal High Frequency Ultrasound Transducers For Medical Applications

Increasing Performances of 1–3 Piezocomposite Ultrasonic Transducer by Alternating Current Poling Method

Enhanced piezoelectric and dielectric properties of AC poled sliver-mode Pb(In1/2Nb1/2)O3-Pb(Mg1/3Nb2/3)O3-PbTiO3 single crystals for ultrasonic abdomen probes

Characterization of Mn-modified Pb(Mg1∕3Nb2∕3)O3–PbZrO3–PbTiO3 Single Crystals for High Power Broad Bandwidth Transducers

High Frequency PMN–PT Single Crystal Focusing Transducer Fabricated by a Mechanical Dimpling Technique

High Frequency Ultrasound Transducer Based on Sm-Doped Pb(Mg1/3Nb2/3)O3-0.28PbTiO3 Ceramic for Intravascular Ultrasound Imaging

AC poling of high Qm and low acoustic impedance Pb(Mg1/3Nb2/3)O3-Pb(Zr,Ti)O3 single crystals produced by a solid-state crystal growth

High Frequency Ultrasound Transducer Based on Sm-Doped Pb(Mg 1/3 Nb 2/3 )O 3 -0.28PbTiO 3 Ceramic for Intravascular Ultrasound Imaging

High Frequency PMN-PT 1-3 Composite Transducer for Ultrasonic Imaging Application

High Performance Relaxor-Based Ferroelectric Single Crystals for Ultrasonic Transducer Applications

High frequency needle ultrasonic transducers based on Mn doped piezoelectric single crystal

80 Mhz Intravascular Ultrasound (ivus) Transducer

Design, fabrication, and evaluation of high frequency, single-element transducers incorporating different materials