Abstract:b Through the ring-opening polymerization of L-lactide initiated by hydroxyl groups on the surface of HNTs using stannous 2-ethylhexanoate as catalyst, halloysite nanotubes surface-grafted with poly (L-lactic acid) (PLLA) segments (g-HNTs) were synthesized. The compositions and morphologies of the modified and unmodified HNTs were observed by Fourier transformation infrared (FTIR), thermal gravimetric analysis (TGA) and transmission electron microscopy (TEM). Then, a series of PLLA, PLLA/HNTs and PLLA/g-HNTs nanofiber membranes were prepared by electrospinning, the influences of the spinning conditions on the morphologies of the nanofiber membranes were discussed, and the composition, micrograph, interfacial compatibility, tensile properties and cellular compatibility of the composite membranes were studied too. Results showed that the grafting percentage of PLLA segments on the surface of g-HNTs was 14.22% as the molar ratio of HNTs to L-lactide was 1:10. The tubular morphology of HNTs changed little after surface grafting, and g-HNTs can easily disperse in anhydrous ethanol. The voltage and the feed rate have effects on the morphology of fiber membranes, when the voltage was 15 kV and feed rate was 1 mL/h, the diameter of the electrospinning fiber was relatively uniform. The dispersion and interfacial compatibility of g-HNTs in PLLA matrix were superior to those of pristine HNTs, when the content of g-HNTs increased up to 40 wt%, the fiber micrograph of the PLLA/g-HNTs composite membranes continues to remain good, and continuous and relatively uniform fiber can be got. With the content of HNTs and g-HNTs increased, the tensile strength and modulus increased first and then decreased, as the filler content was 5 wt%, the highest tensile strengths and moduli were obtained for both of the PLLA/HNTs and PLLA/g-HNTs composite nanofiber membranes. However, the tensile strength and modulus of the PLLA/g-HNTs composite nanofiber membranes were always higher than those of PLLA/HNTs composite nanofiber membranes at all filler contents due to the good adhesive strength between the g-HNTs and PLLA matrix. The results of 3T3 cells culture in vitro indicated that the cellular compatibility of the PLLA/g-HNTs composite nanofiber membranes is very good, and better than that of pure PLLA and PLLA/HNTs nanofiber membranes.

Electrospun Polyvinyl Alcohol/Halloysite Nanotubes Composite Nanofibers

Poly(Vinyl Alcohol)/Hydrotalcite Composite Nanofibre: Preparation And Characterization

Electrospinning Fabrication and Characterization of Poly(Vinyl Alcohol)/Layered Double Hydroxides Composite Fibers

Preparation and Properties of Poly (vinyl Alcohol) Nanofibers by Electrospinning

Preparation and Characterization of Nylon-6/Poly(vinyl Alcohol) Ultrafine No-Woven Fabrics

Electrospinning of Poly(Vinyl Alcoh01)/Gelatin Aqueous Solution

Reactive electrospinning of poly(vinyl alcohol) nanofibers

Synthesis of Nanofiber Polyvinyl Alcohol (PVA) with Electrospinning Method

Manufacture of Electrospun All-Aqueous Poly(vinyl Alcohol)/cellulose Nanocrystal Composite Nanofibrous Mats with Enhanced Properties Through Controlling Fibers Arrangement and Microstructure

Study on morphology of electrospun poly(vinyl alcohol) mats

Preparation of PLLA/g-HNTs Composite Nanofiber Membranes by Electrospinning and Studies on Their Properties

Structural evolution of electrospun composite fibers from the blend of polyvinyl alcohol and polymer nanoparticles.

Fabrication of Poly(vinylidenefluoride‐co‐hexafluoropropylene) Nanofiber Yarns by Conjugate Electrospinning

Synthesis using electrospinning and stabilization of single layer macroporous films and fibrous networks of poly(vinyl alcohol)

Optimization design and properties of PVA/GEL nanofibers

Preparation of PVP/TEOS/Nitrates Composite Nanofibers

Gel spinning of PVA/SWNT composite fiber

Electrospun Polyvinyl Alcohol/waterborne Polyurethane Composite Nanofibers Involving Cellulose Nanofibers

Effects of Various Factors on the Modification of Carbon Nanotubes with Polyvinyl Alcohol in Supercritical CO2 and Their Application in Electrospun Fibers

Electrospinning of Poly(trimethylene Terephthalate)/carbon Nanotube Composites

Electrospinning of Polyvinyl Alcohol into Crosslinked Nanofibers: an Approach to Fabricate Functional Adsorbent for Heavy Metals