Abstract:The present work was undertaken to provide information, lacking in the literature, on the lattice rotation, and the role of twinning during cold rolling of commercial purity titanium (T40). The proposed method consists of determining the individual rotation of the grains induced by low to intermediate deformation (up to 30% in thickness reduction) and following the rotation field using electron backscattered diffraction (EBSD) measurements in a high resolution FEG SEM at different steps of deformation (10 and 20%). We have especially studied the formation, the evolution, and the role of mechanical twins. According to the former research, during deformation at room temperature, three different types of twin systems were activated: ${\left\{ {10\overline {1} 2} \right\}}$ tensile twinning, ${\left\{ {11\overline {2} 2} \right\}}$ compression twinning, and – to a small extent – ${\left\{ {11\overline {2} 1} \right\}}$ tensile twinning depending on the grain orientation. Secondary twins (often ${\left\{ {10\overline {1} 2} \right\}}$ within ${\left\{ {11\overline {2} 2} \right\}}$ twins) were activated in the grains oriented favorably for this secondary twinning. This resulted in a heterogeneous microstructure in which grains were refined in some areas. It also induced reorientation of the c‐axes to stable orientations. No twins of higher order than the second order twins could be found. The rotation flow field was measured by following the rotation of 800 grains. It was possible to determine the individual grains rotations as well as the average flow field. For grains having twinned parts, the lattice rotation of the matrix is similar to that of the grains having a similar crystallographic orientation but without any twins. Twins form in grains having specific orientations with respect to the macroscopic stress field; they can grow in the grain with increasing strain and may consume almost the whole matrix.

3Dxrd Measurements of Lattice Rotations in Tensile Deformed if Steel

Strain Distribution and Lattice Rotations During In-Situ Tension of Aluminum with a Transmodal Grain Structure

Investigation of the Deformation Structure in an Aluminium Magnesium Alloy by High Angular Resolution Three-Dimensional X-Ray Diffraction

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Electron Backscatter Diffraction Analysis of Recrystallized Grains Formed in Deformation Band in Aluminum Single Crystal

In-situ Analysis of Grain Rotation and Lattice Strain Within a Magnesium Polycrystal Based on Synchrotron Polychromatic X-ray Diffraction Technique: (I) Prior to Twin.

In-situ tensile deformation of austenitic stainless steels with various grain sizes during synchrotron and neutron diffraction

In situ synchrotron X-ray multimodal experiment to study polycrystal plasticity

Lattice Rotation and Deformation Mechanisms under Tensile Loading in a Single-Crystal Superalloy with [001] Misorientation

Study of Plastic Deformation in Hexagonal Metals by Interrupted In‐Situ EBSD Measurement

3D microstructural and strain evolution during the early stages of tensile deformation

In Situ Synchrotron X-ray Micro-Diffraction Investigation of Elastic Strains in Laminated Ti-Al Composites

3D microscopy at the nanoscale reveals unexpected lattice rotations in deformed nickel

Large Lattice Strain In Individual Grains Of Deformed Nanocrystalline Ni

In-situ EBSD Study of the Active Slip Systems and Lattice Rotation Behavior of Surface Grains in Aluminum Alloy During Tensile Deformation

Crystallographic orientation and spatially resolved damage for polycrystalline deformation of a high manganese steel

LATTICE DISTORTION STORED ENERGY OF CRYSTALLOGRAPHIC ORIENTATIONS IN COLD-ROLLED LOW CARBON STEEL SHEETS

High-resolution 3D X-ray diffraction microscopy: 3D mapping of deformed metal microstructures

Lattice Rotation Dependence on Microstructural Characteristics in a Low Carbon Steel

In-situ EBSD study of deformation behaviour of 600 MPa grade dual phase steel during uniaxial tensile tests