Abstract:In the conventional wet slurry method for making lithium-ion battery (LIB) electrodes, unwanted N-Methyl-2-Pyrrolidone (NMP) solvent is used. The use of NMP increases the overall energy demand during electrode coating since NMP needs to be dried from the coated slurry and recovered. The improper use of NMP can also impose detrimental effects on health and the environment. Thus, solvent-free dry processes are gaining increased interest worldwide for electrode fabrication. Amongst different dry electrode manufacturing techniques, electrostatic spray deposition (ESD) is one of the most promising techniques. In this study, positive LiNi0.8Co0.1Mn0.1O2 (NMC811) electrodes were manufactured by the ESD process and wet slurry process. The differences between the electrodes made by these two processes were investigated by the peel strength test, electrochemical techniques (e.g., rate tests, electrochemical impedance spectroscopy, and constant voltage/constant current cycling), scanning electron microscopy with energy dispersive x-ray spectroscopy, and X-ray photoelectron spectroscopy. In the dry electrodes, most active material particles were densely covered by the binder and conductive agents. Whereas in wet slurry electrodes, binder and conductive agents were distributed more homogenously both on the active material surfaces and between the active material particles. The uniform distribution of the binder and conductive agents in the slurry electrodes results in a robust conductive network, leading to better performance at high C- rates (e.g., 2-5C). Interestingly, the dry electrodes had comparable performance to slurry electrodes at the initial stages of electrochemical testing with low current rates. Hence, it can be concluded that the distribution of the electrode materials affects active material usage and the conductive paths, and a homogenous distribution is needed to achieve faster discharge capacity at higher C rates. Future work will focus on the long-term cycling performance of the electrodes to further understand the degradation mechanisms and differences between the two types of electrodes.

Study on Prediction of Binder Distribution in the Drying Process of the Coated Web of Positive Electrode for Lithium Ion Battery

Modeling and Optimizing the Drying Process of Electrode Manufacturing for Lithium‐Ion Batteries

Binder migration during drying of lithium-ion battery electrodes: modelling and comparison to experiment

Parametric Energy Consumption Modeling for Cathode Coating Manufacturing of Lithium-Ion Batteries

Numerical Modeling and Analysis of the Binder Migration Behavior During the Dual-Layer Electrode Drying Process

Modeling and Analysis of the Drying Process of Lithium-Ion Battery Electrodes Based on Non-Steady-State Drying Kinetics

Effect of Drying Condition of Poly (vinylidene Fluoride) Binder Solution on Film Adhesion of Graphite Electrode for Lithium Batteries

The Influence of Polyvinylidene Fluoride (PVDF) Binder Properties on LiNi0.33Co0.33Mn0.33O2 (NMC) Electrodes Made by a Dry-Powder-Coating Process

Coarse-grained molecular dynamics simulations of microstructure evolution and debonding in water-based cathode electrode drying

Mechanical and Electrochemical Implications of Drying Temperature on Lithium‐Ion Battery Electrodes

Unveiling the Roles of Binder in the Mechanical Integrity of Electrodes for Lithium-Ion Batteries

The Role of Surface Free Energy in Binder Distribution and Adhesion Strength of Aqueously Processed LiNi 0.5 Mn 1.5 O 4 Cathodes

Numerical simulation of the vacuum drying process of cylindrical lithium-ion batteries

(Invited) Impact of Binder Selection in Advanced Lithium Battery Electrode Fabrication and Performance

A Comparative Study of Different Binders and Their Effects on Electrochemical Properties of LiMn2O4 Cathode in Lithium Ion Batteries

Modeling and Analysis of Solvent Removal During Lithium-Ion Battery Electrode Drying: A Semi-Conjugate Approach

A Formula to Customize Cathode Binder for Lithium Ion Battery

Improvement of Lithium‐Ion Battery Performance by Two‐Layered Slot–Die Coating Operation

Investigating the Structure and Performance Differences between the Electrodes Made by a Dry and a Wet Slurry Processes

Optimization of Drying Process of Lithium Battery Pole Piece Based on Simulation Technology