Abstract:Rectangular AT cut quartz resonators have been widely used in frequency control because of their smal size and extraordinary fequency temperature stability. However, a lot of spurious resonant modes such as face flexure, thickness twist, flexure and their higher order harmonics are coupled to the foundmental thickness shear mode at the edges of the plate. Traditionally only the modes propagating along the width direction are considered for two reasons. Firstly, the rectangular quartz plate dimensions used is often 2?mm×8?mm, that is, the length dimension is much larger than the width dimension. Secondly, the electrode has strong energy trap effect, which means that most of the vibration energy concentrates under the electrode. However, smaller resonators are developed recently, whose width and length dimensions are both less than 3?mm. So, it becomes necessary to take the modes propagating along both x 1 and x 3 directios into account. This paper presents the analysis of the vibration modes in AT cut quartz plate. According to Mindlin's 2 dimensional first order equations, dispersion curves for waves prorogating along x 1 and x 3 directions, in an infinite At cut quartz plate, are obtained. Moreover, after the boundary conditions are considered, standing waves are formed. Then the curves of dimensionless frqunency vs. length/thickness and width/thickness for rectangular AT cut quartz plates, i.e. mode charts, are given in this paper. There is excellent agreement between the computed results and the practical data from the factory. Finally, as an example, the design of a 4 MHz rectangular quartz resonator is shown in this paper. During the design of the resonator, the dimensions of both the width and length are carefully selected in order to avoid the existence of the spurious modes. At the same time, we can see that the computed results do not agree to the pratical data completely, especially at the high frequency range. We can improve the computed results in two ways. Firstly, because there are two correction factors in Mindlin's 2 dimensional first order equations, selecting proper correction may result in preciser mode chart. Secondly, FEM (Finite Element Method) is the desirable solution to the vibration problem of quartz resonator, because of its resilient adaptability to various boundary conditions and different cut orientations.

Effects of Electrode off Centre on Trapped Thickness-Shear Modes in Contoured AT-Cut Quartz Resonators

Trapped Thickness-Shear Modes in a Contoured, Partially Electroded AT-cut Quartz Resonator

Energy Trapping of Thickness-Shear Modes in Inverted-Mesa At-Cut Quartz Piezoelectric Resonators

Effects of Unequal Electrode Thickness, Location, and Size on Thickness-Shear Mode Quartz Piezoelectric Resonators

Effects of Electrode Configuration on Vibration Characteristics of Quartz Thickness-Shear Mode Trapped-Energy Resonators

Thickness-Shear Vibration Characteristics of an At-Cut Quartz Resonator with Rectangular Ring Electrodes

Variational Formulation of the Stevens-Tiersten Equation and Application in the Analysis of Rectangular Trapped-Energy Quartz Resonators

Thickness-shear Modes of an Elliptical, Contoured At-Cut Quartz Resonator

Frequency Shift of Thickness-Shear Vibrations of AT-Cut Quartz Resonators Due to a Liquid Layer with the Electrode Stiffness Considered

Thickness-shear Vibration of an AT-cut Quartz Resonator with a Hyperbolic Contour.

The investigation of trapped thickness shear modes in a contoured AT-cut quartz plate using the power series expansion technique

An analytical and meshless modeling for vibration analysis of an infinite quartz resonator with non-circular electrodes

Variational Analysis of Thickness-Shear Vibrations of a Quartz Piezoelectric Plate with Two Pairs of Electrodes As an Acoustic Wave Filter

Effect of Electrodes on Force–Frequency Characteristics of Rotated Y-Cut Quartz Resonators

Thickness-shear vibration of rotated Y -cut quartz plates with unattached electrodes and asymmetric air gaps

Thickness-shear Frequencies of an Infinite Quartz Plate with Material Property Variation Along the Thickness

THE VIBRATION ANALYSIS AND DESIGN OF AT-CUT RECTANGULAR QUARTZ RESONATORS

A Theoretical Analysis of Mechanical Dissipation of an Electroded Quartz Resonator

Overtone frequency spectra for x3-dependent modes in AT-cut quartz resonators.

Thickness-shear Vibration of AT-cut Quartz Plates Carrying Finite-Size Particles with Rotational Degree of Freedom and Rotatory Inertia [Correspondence]

Effects of laterally heterogeneous slip on the resonance properties of quartz crystals immersed in liquids.