A 0.35 Mu M Cmos 4.8gb/S 4 : 1 Multiplexer(+)

Jh Lu,Zg Wang,L Tian,R Tao,Ht Chen,Tt Xie,Zh Chen,J Feng,Y Dong,Sz Xie

2002-01-01

Abstract:A 4.8Gb/s 4:1 multiplexer was designed in source coupled logic and fabricated in 0.35mum CMOS technology. It has a power dissipation of less than 1W from a 5V supply and a size of 1 X 1.05mm(2), and can be directly applied to optic-fiber link at STM-16 (2.488Gb/s) level of synchronous digital hierarchy (SDH).

What problem does this paper attempt to address?

A 0.35 /spl mu/m CMOS 4.8 Gb/s 4:1 multiplexer

jianhua lu,zhigong wang,lei tian,rui tao,haitao chen,tingting xie,zhiheng chen,jun feng,yi dong,shizhong xie

DOI: https://doi.org/10.1109/icccas.2002.1180739

2002-01-01

Abstract:A 4.8 Gbit/s 4:1 multiplexer was designed in source coupled logic and fabricated in 0.35 /spl mu/m CMOS technology. It has a power dissipation of less than 1W from a 5V supply and a size of 1/spl times/1.05 mm/sup 2/, and can be directly applied to an optical fiber link at STM-16 (2.488 Gbit/s) level of synchronous digital hierarchy (SDH).
10-Gb/S 1 : 4 Demultiplexer In 0.25 Mu M Cmos

L Tian,Zg Wang,Ht Chen,Tt Xie,Jh Lu,R Tao,Y Dong,Sz Xie

DOI: https://doi.org/10.1117/12.444544

2001-01-01

Abstract:This paper describes a 1:4 demultiplexer in a standard 0.25 mum CMOS. A tree-type structure is used to reduce the clock frequency and the SCL (Source Couple Logic) is used to construct high speed DFF. The chip occupies 1mm(2) area. It consumes 693mW from a 3.3 V supply. The operating bit rates is higher than 10Gb/s.
10-Gb/s 1:4 Demultiplexer in 0.25-Μm CMOS

Lei Tian,Zhigong Wang,Haitao Chen,Tingting Xie,Jianhua Lu,Rui Tao,Yi Dong,Shizhong Xie

DOI: https://doi.org/10.1117/12.444544

2001-01-01

Abstract:This paper described a 1:4 demultiplexer in a standard 0.25 micrometers CMOS. A tree-type structure is used to reduce the clock frequency and the SCL (Source Couple Logic) is used to construct high speed DFF. The chip occupies 1mm2 area. It consumes 683mW from a 3.3 V supply. The operating bit rates is higher than 10Gb/s.
Design of A Low-Power 1.5 Gb/S Cmos 1 : 4 Demultiplexer Ic

WC Lu,ZG Wang,L Tian,TT Xie,Y Dong,SZ Xie

DOI: https://doi.org/10.1117/12.444554

2001-01-01

Abstract:This paper presents a 1.5 Gb/s 1:4 demultiplexer IC. It is implemented in a tree-type architecture. The basic cell, i.e. the Flip-Flops, is built up in CMOS pseudo-static logic. The IC was realized in a 0.25mum CMOS technology, and has been measured in an ultra-high speed setup. Opening eye diagrams have been obtained at bit rates up to 1.5 Gb/s. The phase margin at 1.5 Gb/s is greater than 180 degree. The power dissipation of the function core circuit is only 9.5 mW under a supply voltage of 2.5V.
Mach–Zehnder-Based Four-Port Switching Module on SOI

Weiwei Chen,Wanjun Wang,Zhao Gong,Qiang Zhou,Xiaoqing Jiang,Jianyi Yang,Haiquan Zhou

DOI: https://doi.org/10.1109/lpt.2012.2203117

IF: 2.6

2012-01-01

IEEE Photonics Technology Letters

Abstract:In this letter, a Mach-Zehnder-based four-port switching module was designed and fabricated by a 0.8-mu m standard commercial complementary metal-oxide semiconductor line. The module is composed of five electro-optic switching elements and can be used to realize nonblocking switching for the duplex interconnection among four ports. The switching elements are electrically driven with a nanosecond response. Full routing functionality of the four-port switching module is demonstrated with crosstalk levels lower than -11.8 dB under a common spectral bandwidth of 40 nm.
Silicon Mode (de)multiplexers with Parameters Optimized Using Shortcuts to Adiabaticity.

Defen Guo,Tao Chu

DOI: https://doi.org/10.1364/oe.25.009160

IF: 3.8

2017-01-01

Optics Express

Abstract:We propose and experimentally demonstrate broadband silicon mode (de)multiplexers based on the optimization of system adiabaticity using shortcuts to adiabaticity (STA). The measured insertion losses and crosstalks were less than 1.1 dB and -24 dB, respectively, for the five two-mode mode-division-multiplexing (MDM) links over wavelengths ranging from 1500 nm to 1600 nm. The four-mode MDM link showed measured insertion losses and crosstalks less than 1.3 dB and -23 dB, respectively, within the same wavelength range. The method paves the way for future adaptation of the STA protocols to various components.
Three-mode All-Optical (de)multiplexing on a SOI Chip

Yan-Si Le,Zhi Wang,Zhi-Yong Li,Ying Li,Qiang Li,Can Cui,Chong-Qing Wu

DOI: https://doi.org/10.1016/j.optcom.2017.04.059

IF: 2.4

2018-01-01

Optics Communications

Abstract:An on-chip three-mode division multiplexing circuit using a simple ADC-based TE 0 & TE 1 & TE 2 (de)multiplexer is demonstrated to improve the link capacity of on-chip optical interconnects. The proposed (de)multiplexer does not contain any tapered waveguide which is different from the previous mode (de)multiplexer based on ADCs. Here, we choose multimode waveguide width first and then confirm corresponding width of the other two waveguides. Thus the bus waveguide without any tapers can not only reduce complexity of (de)multiplexer but also reduce difficulty of the fabrication. Our simulation results show that the hybrid multiplexer has relatively low loss and low crosstalk about −40 dB, −26.99 dB and −28.72 dB for each mode around 1550 nm with a width-variation w =±25 nm. These properties make the proposed mode-(de)multiplexer suitable for application in high-capacity data transmission.
A 1.27mw 20gbps 1:16 DEMUX with a Symmetrical-Edge-delay Sense Amplifier

Shihao Li,Weixin Gai,Xiao Xiang,Liangxiao Tang,Jichao Huang,Tong Zhao,Xiaoting Zhi

DOI: https://doi.org/10.1109/iscas.2016.7539080

2016-01-01

Abstract:A high-speed low-power 1:16 demultiplexer with a novel symmetrical-edge-delay sense amplifier is presented in this paper. The traditional Sense-Amplifier-Based Flip-Flop (SAFF) has asymmetric rising and falling edges with the fact that the falling edge lags the rising edge the time of a gate delay, which has become a bottleneck of speed. In order to overcome the problem of nonsymmetry of output data edges caused by the set-reset (SR) latch in the Sense-Amplifier-Based Flip-Flop, a new slave latch controlled by the clock is proposed which reduces delay and improves sensitivity considerably. A new type of CMOS logic 2:16 DEMUX is also proposed which can save about 20% area and 15% power consumption compared with the conventional structure. The power consumption of DEMUX is only 0.36mW at the date rate of 10Gb/s and 1.27mW at 20Gb/s. The proposed structure is based on Global Foundry 65nm CMOS process.
A 5-50 Gb/s Quarter Rate Transmitter with a 4-Tap Multiple-Mux Based FFE in 65 Nm CMOS

Xuqiang Zheng,Chun Zhang,Fangxu Lv,Feng Zhao,Shigang Yue,Ziqiang Wang,Fule Li,Zhihua Wang

DOI: https://doi.org/10.1109/esscirc.2016.7598303

2016-01-01

Abstract:This paper presents a 5-50 Gb/s quarter-rate transmitter with a 4-tap feed-forward equalization (FFE) based on multiple-multiplexer (MUX). A bandwidth enhanced 4:1 MUX with the capability of eliminating charge-sharing effect is proposed to increase the maximum operating speed. To produce the quarter-rate parallel data streams with appropriate delays, a compact latch array associated with an interleaved-retiming technique is designed. Implemented in 65 nm CMOS technology, the transmitter occupying an area of 0.6 mm2 achieves a maximum data rate of 50 Gb/s with an energy efficiency of 3.1 pJ/bit.
Ultra-compact Silicon Mode (de)multiplexer Based on Directional Couplers with Subwavelength Sidewall Corrugations

Xiaofei Wang,Nannan Ning,Hui Yu,Yuehai Wang,Jianyi Yang

DOI: https://doi.org/10.1364/ol.449493

2021-01-01

Abstract:Asymmetrical directional couplers aided with subwavelength sidewall corrugations are used to realize ultra-compact silicon mode (de)multiplexers at C-band. Three mode (de)multiplexers with ultra-short coupling lengths of 5.6/6.5/7.7 μm are designed to enable low-loss mode conversions between TE0 and TE1/2/3 modes. They are then cascaded to build a four-channel mode-division-multiplexing (MDM) link. The four mode channels present minimal on-chip insertion losses of 0.2/0.7/0.7/0.9 dB at their peak wavelengths. Measured cross talk levels of the four mode channels are better than -18.0/-19.1/-16.0/-18.2 dB within the wavelength range from 1530 nm to 1580 nm.
Silicon Mode (de)multiplexer Based on Cascaded Particle-Swarm-Optimized Counter-Tapered Couplers

Weiwei Chen,Hongxiang Li,Bohao Zhang,Pengjun Wang,Shixun Dai,Yuxiao Liu,Jun Li,Yan Li,Qiang Fu,Tingge Dai,Hui Yu,Jianyi Yang

DOI: https://doi.org/10.1109/jphot.2020.3046361

IF: 2.4

2020-01-01

IEEE Photonics Journal

Abstract:In this paper, a design of a silicon mode (de)multiplexer based on cascaded counter-tapered couplers is proposed and investigated. By using the particle swarm optimization algorithm and finite difference time domain method, structural parameters of each counter-tapered coupler in our proposed mode (de)multiplexer are optimized so that high conversion efficiencies can be obtained and coupling lengths can be significantly shortened. The coupling lengths of counter-tapered couplers in the proposed silicon four-mode (de)multiplexer operating in transverse-electric polarization are 8 μm, 9 μm, and 10 μm. The corresponding conversion efficiencies are respectively 98.98%, 99.98%, and 98.68%. Experimental results show that, the fabricated device exhibits a demultiplexed crosstalk of -32.76 dB, -27.10 dB, -32.45 dB, or -33.29 dB at 1550 nm wavelength, when the fundamental transverse-electric mode is respectively launched into the ports Input0, Input1, Input2, or Input3. The measured demultiplexed crosstalk is less than -15.15 dB from 1525 to 1596 nm and lower than -18.12 dB from 1525 to 1561 nm.
Novel Wavelength Multiplexer Using (<italic>N</italic> + 1) × (<italic>N</italic> + 1) Arrayed Waveguide Grating and Polarization-Combiner-Rotator on SOI Platform

Jun Zou,Xiao Ma,Xiang Xia,Changhui Wang,Ming Zhang,Jinhua Hu,Xuyang Wang,Jian-Jun He

DOI: https://doi.org/10.1109/JLT.2021.3053837

IF: 4.7

2021-01-01

Journal of Lightwave Technology

Abstract:We propose an ultra-compact novel wavelength multiplexer employing a (N + 1) × (N + 1) arrayed waveguide grating (AWG) and a polarization-combiner-rotator (PCR) on the SOI platform, to realize a multiplexing for 2N wavelengths with a spacing of Δλ. The (N + 1) × (N + 1) AWG works at a bidirectional way to provide two groups of N × 1 wavelength multiplexing with each group having a channel spacing of 2×Δλ, and the central wavelengths of all input channels in one group have a wavelength shift of Δλ with respect to those in the other group. The double channel spacing results in a significant decrease on the footprint of the (N + 1) × (N + 1) AWG-based multiplexer compared with a conventional 2N × 1 AWG multiplexer with the same wavelength spacing Δλ. Due to the fact that a single mode fiber is insensitive to the polarization of input light, if we consider short reach datacom applications such as 100/400 GbE, the two separate multiplexing outputs of the (N + 1) × (N + 1) AWG can be combined as one output with one half wavelengths working at TE polarization and the other at TM polarization by employing a low loss and broadband PCR. In the experiment, we demonstrate a 16 × 200 GHz multiplexer based on a 9 × 9 AWG. The experimental results show that the on-chip loss of the fabricated multiplexer is 2.7 dB and the loss uniformity is 0.5 dB. The 1-dB and 3-dB bandwidths are >0.56 nm (i.e., 35% of the wavelength spacing) and >1.1 nm (i.e., 69% of the wavelength spacing), respectively. They can also be further increased by decreasing the gap between adjacent input waveguides at the interfaces of star couplers of the designed AWG without inducing an excess loss. The proposed multiplexer has great potential for application to future super large capacity (> Tb/s) data transmission systems.
A 4×4 MMI-MZ optical switch matrix on SOI based on carrier injection

YANG Jian,CHEN Wei-wei,WANG Wan-jun,WANG Ming-hua,YANG Jian-yi

DOI: https://doi.org/10.16136/j.joel.2013.01.005

2013-01-01

Abstract:In this paper,a 4×4 optical switch matrix based on free carrier dispersion effect is designed and fabricated on silicon-on-insulator(SOI) water by a 0.8 μm standard commercial CMOS line.It consists of four electro-optic 2×2 multimode imaging-based Mach-Zehnder interferometers.As a basic unit,the proposed switch matrix can be extended to n×n matrix switch and used in both optical space-division and optical time-division switching networks.The two paired MMIs in each Mach-Zehnder structure are used as 3 dB power splitters and combiners.Each switching element is electrically driven with an independent extermal power supply.By injecting free carriers into phase shifter with the active forward P-i-n diode,the π phase shift required for switching action is achieved.Experimental results show that the 4×4 silicon photonic switch matrix has the crosstalk level lower than-8.02 dB with a common spectral bandwidth as large as 35 nm,which is from 1 530 nm to 1 565 nm.Furthermore,when a specific square-wave signal with 10%-90% transition time of 5 ns is loaded,the switching response time is measured to be 17.4 ns for the rising edge and 21 ns for the falling edge,respectively.
An 11.05 Mw/Gbps Quad-Channel 1.25-10.3125 Gbps Serial Transceiver With A 2-Tap Adaptive Dfe And A 3-Tap Transmit Ffe In 40 Nm Cmos

Hong Chen,Dengjie Wang,Ziqiang Wang,Shuai Yuan,Chun Zhang,Zhihua Wang

DOI: https://doi.org/10.1109/ACCESS.2021.3078844

IF: 3.9

2021-01-01

IEEE Access

Abstract:This paper presents a quad-channel 1.25-10.3125 Gbps wireline transceiver implemented in 40 nm CMOS technology. The transmitter consists of a bit width adjustment, a 40:2 multiplexer, a 2:1multiplexer, and a current-mode logic driver with a 3-tap feedforward equalizer. The receiver has a two-stage continuous-time linear equalizer, a 2-tap half-rate fully adaptive decision-feedback equalizer, a phase interpolation-based digital clock and data recovery (CDR) followed by a 2:40 demultiplexer, a bit width adaption. The transceiver also supports AC/DC coupling, CDR locking detection, PLL locking detection, loss of signal detection, automatic termination impedance calibration. A ring VCO-based PLL is designed in each lane to save power consumption, and a dual-core LC VCO-based PLL is implemented in each bank to generate a low jitter clock signal. At 10.3125 Gbps, the transceiver can equalize 28 dB Nyquist loss at a bit error rate of 10(-12), and it consumes 114 mW with a 1.1 V supply. This work presents a high power efficiency of 11.05 mW/Gbps, and the transceiver is suitable for multi-standard applications due to its flexibility and power efficiency.
A 32gb/s 133mw PAM-4 Transceiver with DFE Based on Adaptive Clock Phase and Threshold Voltage in 65nm CMOS.

Liangxiao Tang,Weixin Gai,Linqi Shi,Xiao Xiang,Kai Sheng,Ai He

DOI: https://doi.org/10.1109/isscc.2018.8310210

2018-01-01

Abstract:With the proliferation of the Internet of Things and mobile computing, network speed is accelerating to support data-rich services. This drives the explosion of bandwidth requirement on backplane interconnects while channel length and power efficiency remain intact. This paper presents a 32Gb/s PAM-4 transceiver fabricated in a 65nm CMOS process. It achieves a BER<;10 -12 through 23dB channel loss at 8GHz while consuming 133mW of power.
Optimization of PAM-4 transmitters based on lumped silicon photonic MZMs for high-speed short-reach optical links

Shiyu Zhou,Hsin-Ta Wu,Khosrov Sadeghipour,Carmelo Scarcella,Cormac Eason,Marc Rensing,Mark J Power,Cleitus Antony,Peter O'Brien,Paul D Townsend,Peter Ossieur

DOI: https://doi.org/10.1364/OE.25.004312

2017-02-20

Abstract:We demonstrate how to optimize the performance of PAM-4 transmitters based on lumped Silicon Photonic Mach-Zehnder Modulators (MZMs) for short-reach optical links. Firstly, we analyze the trade-off that occurs between extinction ratio and modulation loss when driving an MZM with a voltage swing less than the MZM's Vπ. This is important when driver circuits are realized in deep submicron CMOS process nodes. Next, a driving scheme based upon a switched capacitor approach is proposed to maximize the achievable bandwidth of the combined lumped MZM and CMOS driver chip. This scheme allows the use of lumped MZM for high speed optical links with reduced RF driver power consumption compared to the conventional approach of driving MZMs (with transmission line based electrodes) with a power amplifier. This is critical for upcoming short-reach link standards such as 400Gb/s 802.3 Ethernet. The driver chip was fabricated using a 65nm CMOS technology and flip-chipped on top of the Silicon Photonic chip (fabricated using IMEC's ISIPP25G technology) that contains the MZM. Open eyes with 4dB extinction ratio for a 36Gb/s (18Gbaud) PAM-4 signal are experimentally demonstrated. The electronic driver chip has a core area of only 0.11mm2 and consumes 236mW from 1.2V and 2.4V supply voltages. This corresponds to an energy efficiency of 6.55pJ/bit including Gray encoder and retiming, or 5.37pJ/bit for the driver circuit only.
A 44 Gbps PAM-4 Transmitter with Resistance Feedback 4:1 MUX in 65nm CMOS

Ziqiang Wang,Dengjie Wang,Xin Wu,Jiawei Wang,Hao Xu,Chun Zhang,Hong Chen,Zhihua Wang

DOI: https://doi.org/10.1109/icsict55466.2022.9963444

2022-01-01

Abstract:This paper presents a power-efficient four-level pulse amplitude modulation (PAM-4) transmitter with 4-tap feed-forward equalizer (FFE) SST driver. A resistance feedback 4:1 MUX is proposed to overcome the bandwidth limit in the last MUX node. The bandwidth is improved more than twice and the jitter is reduced from 7.07ps to 381fs. An absolute delay-based clock distribution network is designed to ensure the timing of the 4:1 MUX. The PAM-4 transmitter is fabricated in 65nm CMOS process and occupies 1.53mm×1.35mm. It delivers a 1.2Vppd PAM-4 signal with RLM of 99% under 1.2V supply and achieves an energy efficiency of 2.27pJ/bit at 44Gbps.
A 4.8-Mw/gb/s 9.6-Gb/s 5 &Lt;inline-Formula> &Lt;tex-Math Notation="tex">$+$</tex-Math></inline-formula> 1-Lane Source-Synchronous Transmitter in 65-Nm Bulk CMOS

Shuai Yuan,Ziqiang Wang,Xuqiang Zheng,Ke Huang,Ni Xu,Woogeun Rhee,Liji Wu,Chun Zhang

DOI: https://doi.org/10.1109/tcsii.2014.2312092

2014-01-01

Abstract:A low-jitter and low-power source-synchronous serializer/deserializer transmitter (TX) with a data rate of 9.6 Gb/s is presented. The TX consists of five data channels plus one forwarded-clock channel and features a total jitter of 20.39 ps p-p at 10 -12 bit error rate. Low jitter is achieved through the use of a phase-locked loop with bandwidth linearization that has a random RMS jitter of 0.66 ps. A global clock distribution network is proposed to minimize the power-supply-induced jitter and the power consumption. The TX transmits preemphasized data through a current-mode logic driver with a four-tap feedforward equalizer. The on-chip output impedance and the signal amplitude can be accurately calibrated by a successive approximation register logic separately. The total power consumption for the 5 +1-lane TX physical core fabricated in 65-nm bulk CMOS running at 9.6 Gb/s is 230 mW or 4.8 mW/Gb/s.
A 10Gb/s source-synchronous transmitter in 65nm CMOS technology

linghan wu,shuai yuan,xuqiang zheng,ziqiang wang,chun zhang

DOI: https://doi.org/10.1109/EDSSC.2014.7061167

2014-01-01

Abstract:This paper describes the design of a source-synchronous transmitter in 65nm CMOS technology. The transmitter consists of five data lanes plus one forwarded clock lane. Every single lane works at 10Gb/s. The clock distribution path is carefully designed to ensure the synchronous of the divided clock in every data lane. And this design is power efficient by optimizing the structure of MUX. Furthermore, a 3 tap feed forward equalizer (FFE) is applied to the driver to compensate channel loss. The experiment result shows that, the output peak-to-peak jitter is 50ps when the transmitter delivers 10Gb/s PRBS7 data over a channel which has a loss of 12.3dB at 5GHz. The power consumption of this circuit is 6.1mW/Gbps for 1.2V supply and the chip area is 1.2mm2.
Compact Silicon 10-Mode Multi/demultiplexer for Hybrid Mode- and Polarisation-Division Multiplexing System.

Weifeng Jiang,Jinye Miao,Tao Li

DOI: https://doi.org/10.1038/s41598-019-49763-0

IF: 4.6

2019-01-01

Scientific Reports

Abstract:To further increase the capacity of the optical transmission system, the hybrid mode- and polarisation-division multiplexing (MDM-PDM) technology has been proved to be an efficient approach by multiplexing dual polarisations for each orthogonal eigen mode. A hybrid (de)multiplexer [(De)MUX] is one of the most important fabrics for the hybrid MDM-PDM networks. A compact silicon 10-mode hybrid (De)MUX is proposed based on three cascaded asymmetric directional couplers (ADCs) based sections, three adiabatic tapers, and a polarisation beam splitter (PBS). The phase-matching conditions can be achieved by varying the widths of the bus waveguides for the TM modes and then by varying the widths of the access waveguides for the TE modes. The simulated results show that a compact total coupling length for TM1 ~ TM3 and TE1 ~ TE5 modes can be achieved to be 55.4 μm. In addition, the total loss of the proposed hybrid (De)MUX can be reduced benefitting from the fewer tapers compared with the conventional cascaded ADCs. The PBS is also optimised with a compact length of 7.0 μm and high extinction ratios of 32.9 dB and 15.4 dB for the TM0 and TE0 modes, respectively.

A 0.35 Mu M Cmos 4.8gb/S 4 : 1 Multiplexer(+)

A 0.35 /spl mu/m CMOS 4.8 Gb/s 4:1 multiplexer

10-Gb/S 1 : 4 Demultiplexer In 0.25 Mu M Cmos

10-Gb/s 1:4 Demultiplexer in 0.25-Μm CMOS

Design of A Low-Power 1.5 Gb/S Cmos 1 : 4 Demultiplexer Ic

Mach–Zehnder-Based Four-Port Switching Module on SOI

Silicon Mode (de)multiplexers with Parameters Optimized Using Shortcuts to Adiabaticity.

Three-mode All-Optical (de)multiplexing on a SOI Chip

A 1.27mw 20gbps 1:16 DEMUX with a Symmetrical-Edge-delay Sense Amplifier

A 5-50 Gb/s Quarter Rate Transmitter with a 4-Tap Multiple-Mux Based FFE in 65 Nm CMOS

Ultra-compact Silicon Mode (de)multiplexer Based on Directional Couplers with Subwavelength Sidewall Corrugations

Silicon Mode (de)multiplexer Based on Cascaded Particle-Swarm-Optimized Counter-Tapered Couplers

Novel Wavelength Multiplexer Using (<italic>N</italic> + 1) × (<italic>N</italic> + 1) Arrayed Waveguide Grating and Polarization-Combiner-Rotator on SOI Platform

A 4×4 MMI-MZ optical switch matrix on SOI based on carrier injection

An 11.05 Mw/Gbps Quad-Channel 1.25-10.3125 Gbps Serial Transceiver With A 2-Tap Adaptive Dfe And A 3-Tap Transmit Ffe In 40 Nm Cmos

A 32gb/s 133mw PAM-4 Transceiver with DFE Based on Adaptive Clock Phase and Threshold Voltage in 65nm CMOS.

Optimization of PAM-4 transmitters based on lumped silicon photonic MZMs for high-speed short-reach optical links

A 44 Gbps PAM-4 Transmitter with Resistance Feedback 4:1 MUX in 65nm CMOS

A 4.8-Mw/gb/s 9.6-Gb/s 5 &Lt;inline-Formula&gt; &Lt;tex-Math Notation="tex"&gt;$+$&lt;/tex-Math&gt;&lt;/inline-formula&gt; 1-Lane Source-Synchronous Transmitter in 65-Nm Bulk CMOS

A 10Gb/s source-synchronous transmitter in 65nm CMOS technology

Compact Silicon 10-Mode Multi/demultiplexer for Hybrid Mode- and Polarisation-Division Multiplexing System.

A 4.8-Mw/gb/s 9.6-Gb/s 5 &Lt;inline-Formula> &Lt;tex-Math Notation="tex">$+$</tex-Math></inline-formula> 1-Lane Source-Synchronous Transmitter in 65-Nm Bulk CMOS