Abstract:Sequential honing process is usually implemented in engine cylinder bore processing to obtain the cross-hatched surface texture with excellent function to balance lubricant storage capacities and supporting performance. Many researches have devoted to correlating honed surface quality of cylinder bore with honing process parameters by means of experiments or simulations. Quite a few efforts have addressed the effect of sequential multiple steps on the surface texture in the honing of engine cylinder bore. However, these researches cannot provide an explicit and analytical methodology to predict honed surface texture efficiently and accurately. This paper presents an analytical and explicit methodology to incorporate a proposed microscale abrasive model into the analytical simulation process of sequential honing. The proposed abrasive model synthetically considers the shape, size, posture, and position of abrasives randomly distributed in honing stone, which is incorporated into honing head motions in terms of rotation, oscillation and feeding. The kinematics of honing head is calculated by space-time discretization to capture the interaction between honing stones and cylinder bore surface. The above procedure acts as each single step for the sequential honing processes. This study investigates the sequential honing of two stages including semi finish honing and plateau honing at different feeding speeds by applying the abrasive model with different abrasive sizes. The formation of cross-hatched surface texture was successfully achieved sequentially by semi-finish honing and plateaus honing. Then the Abbott-Firestone Curve of the honed surface can be obtained to analyze the influences of abrasive size and honing time of two stages on the surface roughness. Correctness of surface roughness predicted by the model is verified by comparing with a group of experiment measurements in terms of Abbott-Firestone Curve. Most errors of all the predicted R-k roughness family roughness parameters in the two honing stages are less than 15%. Based on the model, simulations are done to analyze the influences of abrasive size and honing duration time of two stages on the surface roughness. The result shows that the larger abrasive used in finish honing leads to the decrease of the material portions M-r1, M-r2 and the increase of the reduced valley depth R-vk. The longer plateau honing duration time is preferred to produce the larger M-r1, M-r2 and the smaller R-vk.

SIMULATING THE SEQUENTIAL HONING PROCESS OF ENGINE CYLINDER BORE BY MODELING ABRASIVES IN HONING STONE

Honed Surface Multi-Scale Prediction Based on Multi-Stage Honing Process of Engine Cylinder Bore

Analytically Predicating the Multi-Dimensional Accuracy of the Honed Engine Cylinder Bore

Predicting Microscale Cross-Hatched Surface Texture in Engine Cylinder Bore

Oilstone Processing and Its Impact on the Surface Texture of Cylinder Bore

PREDICTING MULTI-SCALE DIMENSIONAL ACCURACY OF ENGINE CYLINDER BY HONING

Numerical analysis and experimental validation of surface roughness and morphology in honing of Inconel 718 nickel-based superalloy

Free-floating dynamic material removal mechanism of the honing process

Methodology to Improve the Cylindricity of Engine Cylinder Bore by Honing

A Physics-Based Predictive Model for Number of Contact Grains and Grain Depth of Cut in Honing

Simulation to Microtopography Formation of CBN Active Abrasives on a Honing Wheel Surface

Controlling and Optimization of the Honing Trajectory

Simulation Research on the Surface Residual Stress of Ultrasonic Vibration Honing

Investigation on formation mechanism of surface texture and modeling of surface roughness with internal gear power honing

Numerical and Experimental Analysis of the Honing Texture on the Lubrication Performance of Piston Ring–Cylinder Liner Tribosystem

Model of Surface Texture for Honed Gear Considering Motion Path and Geometrical Shape of Abrasive Particle

The Influence of Plateau Honing Process Parameters on Cylinder Bore Surface Roughness

Analysis of Honing Material Removal Rate and Surface Quality Using Electroplated Oilstone

Experimental Investigation of Interactions Between Abrasive Tool and Workpiece in Honing

Coupled Evolution of Piston Asperity and Cylinder Bore Contour of Piston/cylinder Pair in Axial Piston Pump

Theoretical Analysis and Experimental Study of an Adjustable Honing Head for Hole Finishing