Abstract:The three-dimensional grain-averaged response of solid bar samples under non-proportional (NP) elastoplastic axial-torsional loading was investigated using in situ high energy diffraction microscopy (HEDM) and companion crystal plasticity finite element (CPFE) modeling. Important stress metrics including applied shear (σ θZ ) and axial (σ ZZ ) stress tensor components, stress and stress deviator tensor invariants (I 1 , J 2 , and J 3 ), von Mises equivalent stress (), maximum resolved shear stress (mRSS), stress triaxiality (η), and lode angle parameter () values were tracked for ∼ 300 grains under two different loading conditions: (1) Torsion-dominated loading (low NP) and (2) Tension-torsion loading (high NP) in equiatomic NiCoCr, a representative multicomponent face-centered cubic (FCC) superalloy. Overall, significant stress localizations existed within both samples as evidenced by the radial dependence of grain-resolved σ θZ , , and J 2 ; by comparison, I 1 , J 3 , η, and metrics did not show discernable trends within the volume. These stress localizations reveal a complex interplay between axial and shear stress components (e.g., stress coupling) resulting in grain yielding near the sample surface largely driven by shear stress, whereas internal grain yielding was largely accommodated by axial stress. Grain-resolved stress localization trends were described well by the CPFE model, although some discrepancies in magnitude occurred, particularly for volumetric stress metrics (I 1 and η) due to initial type II residual stress distributions. The superposition of initial residual stress states onto CPFE grain-resolved data significantly improved model accuracy for η. This suggests that residual stresses more strongly influence the simulation of volumetric rather than deviatoric (yield) stress metrics.

Synchrotron Measurements of Local Microstructure and Residual Strains in Ductile Cast Iron

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

On the Morphology Variation of Graphite in Ductile Cast Iron through Severe Plastic Deformation

Local Residual Stress in Partially Recrystallized Iron Characterized Using High Resolution Electron Backscatter Diffraction

Relationships Between Macrostructure and Microstructure in Lamellar Graphite Iron Castings

Effect of Grain Size on Deformation and Fracture of Inconel718: an In-Situ SEM-EBSD-DIC Investigation

Measurement and prediction of the transformation strain that controls ductility and toughness in advanced steels

Micromechanical Observation and Numerical Simulation for Local Deformation Evolution of Duplex Stainless Steel

Strain Localizations in Notches for a Coarse-Grained Ni-Based Superalloy: Simulations and Experiments

Copper effects on the microstructures and deformation mechanisms of CoCrFeNi high entropy alloys

In-situ investigation of strengthening and strain hardening mechanisms of Cu-added medium-Mn steels by synchrotron-based high-energy X-ray diffraction

Computational simulation of microstructure evolution during solidification of ductile cast iron

In-situ Study of Microstructural Evolution and Local Strain Distribution During Tensile Loading of Near-Micrometre Grain Size Aluminium

Deformation Localisation in Ion-Irradiated FeCr

Simulating Anisotropic Thermal Conduction in Supernova Remnants I : Numerics and the Evolution of Remnants

Comparative Studies of Constitutive Properties of Nanocrystalline and Bulk Iron During Compressive Deformation

Diffusional and displacive transformations in interstitial-free steel within the scope of a critical assessment of the mechanical property

Activating dispersed strain bands in tensioned nanostructure layer for high ductility: The effects of microstructure inhomogeneity

In situ measurement of three-dimensional intergranular stress localizations and grain yielding under elastoplastic axial-torsional loading

Characterisation of irradiation enhanced strain localisation in a zirconium alloy

3D characterization of closure of surface and internal fatigue cracks in nodular cast iron using Digital Volume Correlation of laboratory X-ray tomography images