Abstract:Amassive number of lithium ion (Li-ion) batteries are used in electric vehicles and the number is still growing rapidly. Li-ion batteries are sensitive to temperature—they likely degrade in an over-cold or an over-hot environment. Battery thermal management systems (BTMSs) are designed to control the battery temperature within the optimal range between 20 and 55°C. Thermal management is one important part of battery management systems. A good BTMS allows researchers to improve the performance, extend the life, and enhance the safety of a battery. We launch this Research Topic to collect the latest technologies and design methodology on BTMSs. Three papers have been published in this issue. Yang et al. designed a semiconductor refrigeration system for a 48 V Li-ion battery pack which often operates at high discharge/charge rates, as shown in Figure 1A. A thermal model of the BTMS was also developed for this semiconductor-based BTMS. This BTMS is integrated with air cooling, limiting the maximum temperature to less than 40°C, as long as the temperature difference is less than 1.6°C. The semiconductor-based BTMS is effective when the battery temperature and discharge rate are high. Wang et al. applied a flat heat pipe (FHP) to a BTMS, utilizing the extremely high thermal dissipation ability of the FHP to remove the heat from the battery, as well as to improve the temperature homogeneity among battery cells. The BTMS structure is presented in Figure 1B. A thermal network model was also developed for this BTMS and the simulation agreed with the experiment data. The thickness, porosity, and particle diameter of a sintered wick on the thermal performance of the battery was investigated and the FHP was optimized. An FHP allows a radiator to be placed aside the battery pack as a condensation sector, making the battery pack compact. Luo et al. designed a novel direct liquid cooling BTMS. With a unique structure shown in Figure 1C, the BTMS can be used for cylindrical battery cells with water as the thermal fluid, without worrying about the potential risks of the electric conductivities of water. A numerical model was developed and validated with the system. They investigated the effects of the coolant flowrate and suggested a high flowrate (>500 mL/min) is needed for the discharge at a rate above 3C of a 20-cell module. Multiple inlets were also suggested to improve the temperature uniformity. These studies have shown new prototypes of battery cooling with semiconductors, heat pipes, and direct liquid cooling, which could provide alternatives for thermal management in commercial battery modules. Edited and reviewed by: Sheng S. Zhang, United States Army Research Laboratory, United States

A Battery Thermal Management System Integrating Immersion Preheating and Immersion Cooling

Theoretical and Experimental Investigations on Liquid Immersion Cooling Battery Packs for Electric Vehicles Based on Analysis of Battery Heat Generation Characteristics

Parametric Investigation on the Performance of a Battery Thermal Management System with Immersion Cooling

A comparative investigation of two-phase immersion thermal management system for lithium-ion battery pack

Numerical study on a novel thermal management system coupling immersion cooling with cooling tubes for power battery modules

Performance of thermal management system for cylindrical battery containing bionic spiral fin wrapped with phase change material and embedded in liquid cooling plate

Performance Analysis of a Battery Thermal Management System Combining Thermoelectric, Composite Phase Change Material, and Liquid Cooling under Extreme Operating Conditions

Numerical and experimental investigations on heat transfer characteristics and influencing factors of immersion cooling system for high-capacity prismatic lithium-ion battery

Simulation and Optimization of Lithium-Ion Battery Thermal Management System Integrating Composite Phase Change Material, Flat Heat Pipe and Liquid Cooling

Experimental study on heat transfer characteristics and Capillary-Assisted enhancement of Dual-Phase immersion battery thermal management system

Cooling and preheating performance of dual-active lithium-ion battery thermal management system under harsh conditions

Battery thermal management system based on the forced-air convection: A review

Editorial: Advanced Battery Thermal Management Systems

Multi-Physics Numerical Analysis of Single-phase Immersion Cooling for Thermal Management of Li-Ion Batteries

Thermal Management of Lithium-Ion Batteries Based on Honeycomb-Structured Liquid Cooling and Phase Change Materials

Thermal Performance Analysis of a Lithium-Ion Battery Thermal Management System with a Vapor Chamber and Minichannel Cold Plate

Heat transfer characteristics and influencing factors of immersion coupled direct cooling for battery thermal management

Single-phase static immersion-cooled battery thermal management system with finned heat pipes

Numerical study on heat dissipation performance of a lithium-ion battery module based on immersion cooling

A Review of the Power Battery Thermal Management System with Different Cooling, Heating and Coupling System

Comparative Evaluation of Liquid Cooling-Based Battery Thermal Management Systems: Fin Cooling, PCM Cooling, and Intercell Cooling