Abstract:Electrochemical energy storage devices (EESDs) such as metal-air batteries (MABs) and alkaline electrolyte membrane fuel cells (AEMFCs) have begun to gain vast amounts of attention due to their high theoretical energy densities and open-circuit voltage values. Although these devices present promising aspects for the environment and sustainability, they suffer from the slow reaction kinetics and degradation effects that occur at the catalyst layer interface of the air electrode. Typically, these effects are due to the accumulation of molecular species such as water or oxygen at catalyst active sites because of poor electrode hydrophobicity and fluid management. Herein, we perform experimentation to mitigate these effects by implementing mixed carbon composite microporous layers onto porous carbon felt based air electrodes. This adaptation of the air cathode was predominantly based on the aforementioned downfalls and the lack of availability of commercial carbon felts that have adequate wet proofing and conductivity like some of the related carbon paper gas diffusion layers. Microporous layers (MPLs) enhance electrical conductivity, surface area, and adhesion at the catalyst layer and gas diffusion layer interface. These layers typically consist of a hydrophobic polymer such as polytetrafluoroethylene (PTFE) and a conductive carbon black substrate such as Ketjen Black 600JD (KJB). The incorporation of multi-walled carbon nanotube (MWCNT) and carbon black composites into the structure of the MPLs drastically decreases ohmic polarization with minimal increases in specific resistance. The electrical resistance of the synthesized carbon substrate decreases at high rates of MWCNT dispersion, which corresponds directly to a low MWCNT weight percentage within the composite. The MPL increases the mass transport through the electrode by mitigating flooding effects that typically occur within the pores near the surface of the catalyst layer, ultimately aiding in charge transfer between the gas diffusion layer and catalyst active sites. Preliminary data from AEMFC symmetric cell tests suggests that a microporous layer consisting of a 10 wt.% MWCNT/KJB (m/m) substrate is the optimal loading of carbon nanotubes and leads to better cell performance. There is an increase in current density of 60 mA/cm 2 compared to an air electrode with no MPL within the ohmic region of the polarization curve corresponding to approximately 0.7 V, while only an increase of 18 mA/cm 2 is seen for an MPL consisting of a 30 wt.% MWCNT/KJB (m/m) carbon substrate. The increase of charge transfer by the 10 wt.% synthesized carbon substrate MPL was attributed to the ability of the nanotubes at high rates of dispersion to act as molecular wires within the electrode. Additionally, zinc-air battery tests using the optimally configured air electrode, determined from previous experiments, show that the current density at an operating voltage of 1.1 V was increased by 2.3 times that of an electrode without an MPL using the same catalyst material and loading. Significantly, this research will lead to a better understanding of optimization of the air electrode used within electrochemical devices and how to eliminate some of the adverse effects associated with it. Figure 1

Gas diffusion electrode and preparation and application thereof

Non-noble-metal porous-framework gas diffusion electrode as well as preparation and application thereof

ORDERED MEMBRANE ELECTRODE, PREPARATION AND APPLICATION THEREOF

Development of Cathode Ordered Membrane Electrode Assembly Based on TiO2 Nanowire Array and Ultrasonic Spraying

Converting CO 2 to multi-carbon products at >1 A/cm 2 using gas diffusion electrode based on commercial materials via transfer process engineering

Fuel cell ordered porous nano-fiber single electrode, membrane electrode and preparation method

Converting CO2 to Multi-Carbon Products at >1 A/cm2 Using Gas Diffusion Electrode Based on Commercial Materials Via Transfer Process Engineering

Catalyst Electrodes with PtCu Nanowire Arrays In Situ Grown on Gas Diffusion Layers for Direct Formic Acid Fuel Cells

Boosting the Faradaic Efficiency for Carbon Dioxide to Monoxide on a Phthalocyanine Cobalt Based Gas Diffusion Electrode to Higher Than 99% Via Microstructure Regulation of Catalyst Layer

Effect of gas diffusion layer surface property on platinum nanowire array electrode performance in proton exchange membrane fuel cells

Porous Bilayer Electrode‐Guided Gas Diffusion for Enhanced CO2 Electrochemical Reduction

Research on flaky and vertical gas diffusion electrode

Effect of Catalyst Layer Location on Performance of Gas Diffusion Electrode

An Ultra-Thin, Flexible, Low-Cost and Scalable Gas Diffusion Layer Composed of Carbon Nanotubes for High-Performance Fuel Cells

Gas diffusion enhanced electrode with ultrathin superhydrophobic macropore structure for acidic CO 2 electroreduction

Tailoring Pore Networks – Gas Diffusion Electrodes via Additive Manufacturing

Scalable Gas Diffusion Electrode Fabrication for Electrochemical CO2 Reduction Using Physical Vapor Deposition Methods.

(Digital Presentation) Evaluating the Performance of Multi-Walled Carbon Nanotube Composite Microporous Layers Deposited on Carbon Felt Gas Diffusion Layers

Catalyst electrode based on in-situ grown Pt nanowires

Novel Fabrication Approach by Reversely Coating a Nafion Ionomer on Gas Diffusion Electrodes for High-Performance Membrane Electrode Assemblies

Pore Engineering in Gas Diffusion Layer of Phthalocyanine Cobalt Cathode to Promote Electrochemical CO2-to-CO Reduction