Abstract:Centrifugal compressors are deemed to have a wide operating range. Recirculation devices, which comprise a bleed slot, an upstream slot and an annular cavity connecting them, are often used particularly compressors for turbochargers. They remove low energy fluid at the inducer and improve the incidence angle of the impeller leading edge, i.e. the blade loading of the inducer, at low flow rates due to the recirculation flow supplied to the compressor inlet. The impeller of a centrifugal compressor is often housed in a volute. Since the geometry of the volute is not axisymmetric, the impeller might be surrounded by an asymmetric flow field, hence there is the potential to enlarge the compressor operating range and improve efficiency using a recirculation device with an asymmetrically-distributed bleed slot, referred to here as a non-axisymmetric recirculation device.The authors [1] applied non-axisymmetric recirculation devices to a compressor with a vaneless diffuser. The results showed the effectiveness of a non-axisymmetric recirculation device with a bleed slot partially channeled in the circumferential direction. They also showed that the surge line of the compressor characteristics, which is the line connecting the operational points of the smallest flow rates on all peripheral Mach numbers, was significantly affected by the change in the circumferential position of the bleed slot relative to the volute tongue. The tested compressor was originally designed to feature a vaned diffuser [2]. Enhancing the compressor operating range is the key for marine use turbochargers, integrally geared compressors, multistage compressors and gas turbines as well as automotive turbochargers. These compressors normally use vaned diffusers. In this study the authors tried to apply non-axisymmetric recirculation devices developed in their previous study [1] to compressors with a vaned diffuser. Moreover different circumferential positions of the bleed slot relative to the volute tongue were tested as well as the vanelss diffuser case. The change in the surge line of the compressor characteristics was much smaller compared to the compressor with the vaneless diffuser. The circumferential static pressure distributions in the compressors in combination with vaneless and vaned diffusers were measured to determine the above reason as well as conducting unsteady calculations with a simplified outlet boundary condition. These measurements and calculations showed that the impeller with the vaned diffuser was surrounded by a less distorted static pressure field than that with the vaneless diffuser. These results implied that the vaned diffuser depresses the spread of the circumferential static pressure non-uniformity effect caused by a volute to the impeller.

Centrifugal compressor with asymmetrical vaneless diffuser and automobile with same

Centrifugal compressor with asymmetrical vane-less diffusers and producing method thereof

Centrifugal compressor using asymmetrical bladed diffuser with variable mounting angles in circumferential direction

Compressor using asymmetrical bladed diffuser with variable mounting angles and consistency coupling

Controllable profile vaneless diffuser for centrifugal compressor

Experimental investigation of transient characteristics of mild surge and diffuser rotating stall in a centrifugal compressor with vaned diffuser

Non-Axisymmetric Flow Structure in Vaneless Diffuser of Centrifugal Compressor for Turbochargers

Centrifugal air compressor adopting non-linear distribution of area-radius ratio (A/r) of volute passage section

Stability Improvement Of Turbocharger Centrifugal Compressor By Asymmetric Vaneless Diffuser Treatment

Effect of Circumferential Static Pressure Non-Uniformity Caused by A Volute on Flow in High Pressure Ratio Centrifugal Compressor with Vaneless and Vaned Diffuser

Centrifugal compressor with inlet guide blades and turbocharger

Centrifugal compressor asymmetrical self-circulation casing treatment based on variable slot width

Stability Improvement Of A Turbocharger Centrifugal Compressor By A Nonaxisymmetric Vaned Diffuser

Application and Investigation of Vane Diffuser on Small Flow Centrifugal Compressor

Flow instability suppression and deep surge delay by non-axisymmetric vaned diffuser in a centrifugal compressor

Influence of Volute Distortion on the Performance of Turbocharger Centrifugal Compressor with Vane Diffuser

Influence of volute-induced distortion on the performance of a high-pressure-ratio centrifugal compressor with a vaneless diffuser for turbocharger applications

Blade forward-swept centrifugal compressor and turbocharger

Design of A Single-Stage Centrifugal Compressor and Numerical Investigation of Simultaneous Adjustment of Inlet Guide Vanes and Diffuser Vanes

Investigation of vaned diffuser endwall contouring technology for improving the stable operating range of a centrifugal compressor with an asymmetric volute

Applications of Additively Manufactured Adjustable Vaned Diffusers in Centrifugal Compressor