Abstract:Centrifugal compressors are deemed to have a wide operating range. Recirculation devices, which comprise a bleed slot, an upstream slot and an annular cavity connecting them, are often used particularly compressors for turbochargers. They remove low energy fluid at the inducer and improve the incidence angle of the impeller leading edge, i.e. the blade loading of the inducer, at low flow rates due to the recirculation flow supplied to the compressor inlet. The impeller of a centrifugal compressor is often housed in a volute. Since the geometry of the volute is not axisymmetric, the impeller might be surrounded by an asymmetric flow field, hence there is the potential to enlarge the compressor operating range and improve efficiency using a recirculation device with an asymmetrically-distributed bleed slot, referred to here as a non-axisymmetric recirculation device.The authors [1] applied non-axisymmetric recirculation devices to a compressor with a vaneless diffuser. The results showed the effectiveness of a non-axisymmetric recirculation device with a bleed slot partially channeled in the circumferential direction. They also showed that the surge line of the compressor characteristics, which is the line connecting the operational points of the smallest flow rates on all peripheral Mach numbers, was significantly affected by the change in the circumferential position of the bleed slot relative to the volute tongue. The tested compressor was originally designed to feature a vaned diffuser [2]. Enhancing the compressor operating range is the key for marine use turbochargers, integrally geared compressors, multistage compressors and gas turbines as well as automotive turbochargers. These compressors normally use vaned diffusers. In this study the authors tried to apply non-axisymmetric recirculation devices developed in their previous study [1] to compressors with a vaned diffuser. Moreover different circumferential positions of the bleed slot relative to the volute tongue were tested as well as the vanelss diffuser case. The change in the surge line of the compressor characteristics was much smaller compared to the compressor with the vaneless diffuser. The circumferential static pressure distributions in the compressors in combination with vaneless and vaned diffusers were measured to determine the above reason as well as conducting unsteady calculations with a simplified outlet boundary condition. These measurements and calculations showed that the impeller with the vaned diffuser was surrounded by a less distorted static pressure field than that with the vaneless diffuser. These results implied that the vaned diffuser depresses the spread of the circumferential static pressure non-uniformity effect caused by a volute to the impeller.

Non-Axisymmetric Flow Structure in Vaneless Diffuser of Centrifugal Compressor for Turbochargers

Experimental investigation of transient characteristics of mild surge and diffuser rotating stall in a centrifugal compressor with vaned diffuser

Stability Improvement Of A Turbocharger Centrifugal Compressor By A Nonaxisymmetric Vaned Diffuser

Over-all performance analysis of a dual-entry turbocharger compressor with variable geometry orifice

Stability Improvement Of Turbocharger Centrifugal Compressor By Asymmetric Vaneless Diffuser Treatment

Stability Improvement of High-Pressure-Ratio Turbocharger Centrifugal Compressor by Asymmetric Flow Control-Part I: Non-Axisymmetrical Flow in Centrifugal Compressor.

Effect of Circumferential Static Pressure Non-Uniformity Caused by A Volute on Flow in High Pressure Ratio Centrifugal Compressor with Vaneless and Vaned Diffuser

Influence of Volute Design on Flow Field Distortion and Flow Stability of Turbocharger Centrifugal Compressors

Influence of the Volute on the Flow in a Centrifugal Compressor of a High-Pressure Ratio Turbocharger

Investigation of the Instability Mechanisms in a Turbocharger Centrifugal Compressor with a Vaneless Diffuser by Means of Unsteady Simulations

Performance Improvement of a High Loading Centrifugal Compressor with Vaned Diffuser by Hub Contour Optimization

Influence of Volute Distortion on the Performance of Turbocharger Centrifugal Compressor with Vane Diffuser

Flow instability suppression and deep surge delay by non-axisymmetric vaned diffuser in a centrifugal compressor

Investigation Of Vaned Diffuser Splitters On The Performance And Flow Control Of High Pressure Ratio Centrifugal Compressors

Influence of volute-induced distortion on the performance of a high-pressure-ratio centrifugal compressor with a vaneless diffuser for turbocharger applications

Full Annulus Simulation on a Multistage Axial-Centrifugal Combined Compressor

A Novel Experimental Method to Evaluate the Impact of Volute’s Asymmetry on the Performance of a High Pressure Ratio Turbocharger Compressor

Of vaned diffuser splitters on the performance of a and flow control high pressure ratio centrifugal compressor

Investigation of vaned diffuser endwall contouring technology for improving the stable operating range of a centrifugal compressor with an asymmetric volute

Inlet Duct Treatment for Stability Improvement on a High Pressure Ratio Centrifugal Compressor

Centrifugal compressor with asymmetrical vaneless diffuser and automobile with same