Abstract:Redox flow batteries are emerging as a promising method to provide grid-scale power and long-duration energy storage safely and economically. The thermally regenerative ammonia battery (TRAB) is a new redox flow battery category that can be recharged using low-grade waste heat rather than electric energy, adding further flexibility to the applicability of flow battery systems. Recently, a new TRAB with all-aqueous electroactive species (referred to as the Cu aq -TRAB), as opposed to deposition-dissolution reactions, was found to have superior energy and power densities relative to competing TRABs. The use of bromide and ammonia stabilizes for both Cu(I) and Cu(II) oxidation states, while also creating a cell potential of up to 1.0 V. The potential can be recovered by thermally separating ammonia from the electrolyte and adding it back to alternate electrolyte chambers in successive cycles. Potential improvements in overall cell performance are possible by reducing ohmic losses associated with membrane selection. However, the ideal membrane for the Cu aq -TRAB is not obvious and raises interesting transport questions relative to the dominant redox-active copper species being negatively charged in the catholyte but positively charged in the anolyte. Furthermore, membrane crossover of ammonia, a small, uncharged molecule, was previously shown to be a primary source of parasitic losses for TRABs. Therefore, we investigated how different membrane types (cation, anion, and non-selective) affected ion transport and TRAB performance. A batch symmetry cell was used to determine membrane conductivity in the Cu aq -TRAB environment and membrane diffusion coefficients of each species in the electrolytes. Flow cell experiments were also conducted to find peak power, energy density, average power during discharge, and capacity fade over successive electric charge/discharge cycles. Tradeoffs between membrane conductivity and permeability observed in the symmetry cell are manifested in flow cell results as either high peak and average power or high energy density and low capacity fade. These results expand on potential methods for controlling transport in redox flow batteries and demonstrate the potential for non-selective membranes for electrochemical energy technologies.

Modelling of a Bimetallic Thermally-Regenerative Ammonia Flow Battery for Conversion Efficiency and Performance Evaluation

A Bimetallic Thermally-Regenerative Ammonia-Based Flow Battery for Low-Grade Waste Heat Recovery

Analysis and Optimization of Thermally-Regenerative Ammonia-Based Flow Battery Based on a 3-D Model

A bimetallic thermally regenerative ammonia-based battery for high power density and efficiently harvesting low-grade thermal energy

Understanding the Reaction Mechanism and Self-Discharge of a Bimetallic Thermally-Regenerative Ammonia Battery

An Electrolyte-Decoupled Ammonia Battery for Enhancing Electricity Production from Low-Grade Waste Heat

A Numerical Investigation of the All-Aqueous Copper Thermally Regenerative Ammonia Battery

Temperature characteristics of a copper/zinc thermally-regenerative ammonia battery

Simulating Discharge Curves of an All-Aqueous TRAB to Identify Pathways for Improving System Performance

High Power Thermally Regenerative Ammonia-Copper Redox Flow Battery Enabled by a Zero Gap Cell Design, Low-Resistant Membranes, and Electrode Coatings

System efficiency and power assessment of the all-aqueous copper thermally regenerative ammonia battery

A Numerical Model for a Thermally Regenerative Electrochemical Cycled Flow Battery for Low-Temperature Thermal Energy Harvesting

The Impacts of Electrolyte Composition on Key Performance Metrics of the All-Aqueous Copper Thermally Regenerative Ammonia Battery

Thermally Regenerative Flow Batteries with pH Neutral Electrolytes for Harvesting Low-Grade Heat

Enhancing Low-Grade Thermal Energy Recovery in A Thermally Regenerative Ammonia Battery Using Elevated Temperatures

Effect of operating parameters on the performance of thermally regenerative ammonia-based battery for low-temperature waste heat recovery

Performance of a non-aqueous nanofluid thermally regenerative flow battery for electrical energy recovery from low-grade waste heat

A Thermally-Regenerative Ammonia-Based Flow Battery for Electrical Energy Recovery from Waste Heat

Power and energy capacity tradeoffs in an all-aqueous copper thermally regenerative ammonia battery

Performance of a thermally regenerative ammonia-based battery using gradient-porous copper foam electrodes

Membrane Transport and Performance in the All-Aqueous Copper Thermally Regenerative Battery