Abstract:This work aims to study a possible modification in the electronic structure of scandia-ceria-stabilized zirconia (10Sc1CeSZ) ceramics sintered at different temperatures. In addition to using X-ray diffraction (XRD), scanning electron microscopy (SEM) and impedance spectroscopy to investigate the structural and electrical properties, we employed X-ray photoelectron spectroscopy (XPS) to determine the chemical state information of the atoms involved, along with compositional analysis. As expected, a significant increase in grain ionic conductivity with the sintering temperature was present. This increase was accompanied by a decrease in the porosity of the samples, an increase in the grain size, and a transformation from the rhombohedral to the cubic phase. The phase transformation was detected not only using XRD, but also using XPS and, for this type of ceramic, XPS detected this transformation for the first time. In addition to the changes in the structural characteristics, the increase in the ionic conductivity was accompanied by a modification in the electronic structure of the ceramic surface. The XPS results showed that the surface of the ceramic sintered at the lower temperature of 1100 °C had a higher amount of Zr-OH bonds than the surface of the ceramic sintered at the higher temperature of 1400 °C. The existence of these Zr-OH bonds was confirmed using Fourier-transform infrared spectroscopy (FTIR). From this result, taken together with the difference between the oxygen/zirconium ratios in these ceramics, also identified using XPS, we conclude that there were fewer oxygen vacancies in the ceramic sintered at the lower temperature. It is argued that these two factors, together with the changes in the structural characteristics, have a direct influence on the conductive properties of the studied ceramics sintered at different temperatures.

Structure and Electrical Properties of Cold Sintered 8mol% Scandia Stabilized Zirconia Ceramics

Improved Mechanical Properties of 3YSZ Ceramics Prepared by Pressure-less Sintering Assisted by Cold Sintering under Mild Conditions

Scandia-stabilized Zirconia-Impregnated (la, Sr)MnO 3 Cathode for Tubular Solid Oxide Fuel Cells

Homogeneous Precipitation Synthesis and Electrical Properties of Scandia Stabilized Zirconia

Doped Zirconia/Ceria Electrolyte Fabricated at Low Temperature

The Influence Of Microstructure And Grain Boundary On The Electrical Properties Of Scandia Stabilized Zirconia

Scandia-stabilized Zirconia Electrolyte with Improved Interlamellar Bonding by High-Velocity Plasma Spraying for High Performance Solid Oxide Fuel Cells

High-conductivity electrolyte with a low sintering temperature for solid oxide fuel cells

The research of crystal structure and electrical properties of a new electrolyte material: Scandia and holmia stabilized zirconia

The Properties of YSZ Electrolyte Sintering at 1300 °C

Modified Sol-gel Method used for Obtaining SOFC Electrolyte Materials

Effect of Sintering Conditions on the Microstructure and Electrochemical Properties of 6Scandia 1Ceria co-doped Zirconia (6Sc1CeZr)

X-ray Photoelectron Spectroscopy Analysis of Scandia-Ceria-Stabilized Zirconia Composites with Different Transport Properties

The Propertied Of Ysz Electrolyte Sintering At 1300 Degrees Enc

Grain Size-Dependent Electrical Conductivity in Scandia-Stabilized Zirconia Prepared by a Mild Urea-Based Hydrothermal Method

Research on Sintering Process of YSZ Electrolyte

Preparation of dense ScSZ thin films by plasma spraying with densified ScSZ powders

Study on the Properties of Ysz Electrolyte Made by Plaster Casting Method and the Applications in Solid Oxide Fuel Cells

Al2O3 Toughening ScSZ Electrolyte Fabricated by Water-Based Tape Casting Technique for Solid Oxide Fuel Cells

High Performance Solid Oxide Fuel Cells Based on Tri-Layer Yttria-Stabilized Zirconia by Low Temperature Sintering Process

Preparation and Electrical Properties Test of Yttria Stabilized Zirconia