Abstract:Drinking water utilities are interested in upgrading their treatment facilities to enhance micropollutant removal and byproduct control. Pre-oxidation by chlorine dioxide (ClO2) followed by coagulation-flocculation-sedimentation and advanced oxidation processes (AOPs) is one of the promising solutions. However, the chlorite (ClO2-) formed from the ClO2 pre-oxidation stage cannot be removed by the conventional coagulation process using aluminum sulfate. ClO2- negatively affects the post-UV/chlorine process due to its strong radical scavenging effect, and it also enhances the formation of chlorate (ClO3-). In this study, dosing micromolar-level ferrous iron (Fe(II)) into aluminum-based coagulants was proposed to eliminate the ClO2- generated from ClO2 pre-oxidation and benefit the post-UV/chlorine process in radical production and ClO3- reduction. Results showed that the addition of 52.1-µmol/L FeSO4 effectively eliminated the ClO2- generated from the pre-oxidation using 1.0 mg/L (14.8 µmol/L) of ClO2. Reduction of ClO2- increased the degradation rate constant of a model micropollutant (carbamazepine) by 55.0% in the post-UV/chlorine process. The enhanced degradation was verified to be attributed to the increased steady-state concentrations of HO· and ClO· by Fe(II) addition. Moreover, Fe(II) addition also decreased the ClO3- formation by 53.8% in the UV/chlorine process and its impact on the formation of chloro-organic byproducts was rather minor. The findings demonstrated a promising strategy to improve the drinking water quality and safety by adding low-level Fe(II) in coagulation in an advanced drinking water treatment train.

Understanding the Coagulation Mechanism and Floc Properties Induced by Fe(VI) and FeCl3: Population Balance Modeling.

Study on Influence Factors in Flocculation Conditions of Bioflocculant

Enhanced Coagulation-Flocculation Performance of Iron-Based Coagulants: Effects of PO4(3-) and SiO3(2-) Modifiers

The Formation of Planar Crystalline Flocs of Γ-Feooh in Fe(II) Coagulation and the Influence of Humic Acid

The Impact of Small Organic Molecules on Fe(II) Coagulation: Facilitating Vs. Shielding Mechanisms on Charge Transfer

Influential factors of formation kinetics of flocs produced by water treatment coagulants.

Evaluation of kaolin floc characteristics during coagulation process: a case study with a continuous flow device

Atomic-Level Structural Differences between Fe(III) Coprecipitates Generated by the Addition of Fe(III) Coagulants and by the Oxidation of Fe(II) Coagulants Determine Their Coagulation Behavior in Phosphate and DOM Removal

Effects of Fe(II)/P Ratio and Ph on Phosphorus Removal by Ferrous Salt and Approach to Mechanisms

The Influence of Various Additives on Coagulation Process at Different Dosing Point: from a Perspective of Structure Properties

The impact of pH on floc structure characteristic of polyferric chloride in a low DOC and high alkalinity surface water treatment.

Characterization and coagulation–flocculation performance of a composite coagulant: poly-ferric-aluminum-silicate-sulfate

Optimization of hydrodynamic conditions in coagulation process and study of floc size characteristics

[Effect of Natural Organic Matter on Coagulation Efficiency and Characterization of the Flocs Formed].

Effects of operational conditions on the floc formation time and rate in magnesium hydroxide coagulation process

Aggregation behavior and mechanism of kaolin particles suspension in the presence of Xanthan gum and Fe(III)

Dosing low-level ferrous iron in coagulation enhances the removal of micropollutants, chlorite and chlorate during advanced water treatment

Mechanism and Efficiency of Tetracycline Removal by Ferrate and Ferrous-Enhanced Ferrate System

Coagulation characteristic and mechanism of Fe(III) salts toward typical Cr(III) complexes in wastewater treatment

Membrane Fouling on Coagulation/aid-Coagulation/ultrafiltration Process for Drinking Water Treatment

Influence of Impurities on Stability of Composite Ferrate Solution