Abstract:Solid polymer electrolytes (SPEs) are preferable in the pursuit for developing high-energy Li metal batteries due to their inherent flexibility and intimate contact with electrodes. However, continuous interfacial parasitic reactions and undesired Li dendrite growth caused by inhomogeneous plating/stripping of Li+ result in rapid deterioration of an SPE/Li interface. Herein, a novel Zn2+-containing SPE (SPE-xZn) with anionic groups partially tethered on the polymer chains is developed to meet these challenges. During cycling, Zn2+ cations inside the SPE-xZn will gradually migrate to the surface of a Li electrode and then evolve to a Li-Zn alloy layer, where Li+ can diffuse more efficiently. Meanwhile, owing to the electrostatic interaction, the immobilized anionic groups within SPE-xZn can alleviate local concentrated Li+ flux. The synergistic effects of an in situ formed alloy layer and unique macromolecular structure can promote uniform plating/stripping of Li, thus yielding a more stable SPE-xZn/Li interface. Therefore, steady cycling over 300 h at 0.2 mA cm–2 is achieved by Li/SPE-5Zn/Li, and an impressive capacity retention of 87.3% at 0.5 C after 800 cycles is realized by LFP/SPE-5Zn/Li with an average Coulombic efficiency of 99.90%.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acssuschemeng.1c00878?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acssuschemeng.1c00878</a>.TGA profiles of SPE-xZn Ar and N2 atmospheres (Figure S1); flame tests of SPE-0Zn and SPE-5Zn (Figure S2); tc (Figure S3) and LSV (Figure S4) tests for SPE-0Zn, SPE-2.5Zn, SPE-7.5Zn, and SPE-10Zn; cycling performance of the Li/SPE-PEO/Li cell (Figure S5); FT-IR (Figure S6) and XPS (Figure S7) for SPE-0Zn and SPE-5Zn before and after cycling; cycling performance of the LFP/SPE-PEO/Li cell (Figure S8); thickness of SPE-xZn and SPE-PEO (Table S1); and ionic conductivity of SPE-xZn at varying temperatures (Table S2) (<a class="ext-link" href="/doi/suppl/10.1021/acssuschemeng.1c00878/suppl_file/sc1c00878_si_001.pdf">PDF</a>)Flame tests for SPE-PEO and SPE-5Zn (Video 1) (<a class="ext-link" href="/doi/suppl/10.1021/acssuschemeng.1c00878/suppl_file/sc1c00878_si_002.mp4">MP4</a>)This article has not yet been cited by other publications.

Spontaneous in Situ Surface Alloying of Li-Zn Derived from a Novel Zn2+-Containing Solid Polymer Electrolyte for Steady Cycling of Li Metal Battery

Spontaneous In Situ Surface Alloying of Li-Zn Derived from a Novel Zn 2+ -Containing Solid Polymer Electrolyte for Steady Cycling of Li Metal Battery

Solvent-free In-Situ Polymerized Plastic Crystal Electrolytes for Long-Cycling Lithium Metal Batteries

MXene Surface Engineering Enabling High‐Performance Solid‐State Lithium Metal Batteries

Stabilization of the Li Metal Anode Through Constructing a LiZn Alloy/polymer Hybrid Protective Layer Towards Uniform Li Deposition

Interphase Optimum via Synergistic Effect of Poly(1,3‐dioxolane) Electrolytes and Lithium Difluorophosphate for Stable Lithium Metal Batteries

Polyacrylonitrile Fibers Network Reinforced Polymer Electrolyte with Li-Sn Alloy Layer Protected Li Anode Toward Ultra-Long Cycle Lifespan for Room-Temperature Solid-State Batteries

Dynamic Concentration of Alloying Element on Anode Surface Enabling Cycle‐Stable Li Metal Batteries

Lithiophilic Li-Si alloy-solid electrolyte interface enabled by high-concentration dual salt-reinforced quasi-solid-state electrolyte

Armoring lithium metal anode with soft–rigid gradient interphase toward high-capacity and long-life all-solid-state battery

In situ initiator-free gelation of highly concentrated lithium bis(fluorosulfonyl)imide-1,3-dioxolane solid polymer electrolyte for high performance lithium-metal batteries

In Situ Polymerization Design of a Quasi-Solid Electrolyte Enhanced by NMP Additive for Lithium Metal Batteries

Solid polymer electrolyte soft interface layer with 3D lithium anode for all-solid-state lithium batteries

Polyfluorinated crosslinker-based solid polymer electrolytes for long-cycling 4.5 V lithium metal batteries

A Three-Dimensional Co-Continuous Network Structure Polymer Electrolyte with Efficient Ion Transport Channels Enabling Ultralong-Life All Solid-State Lithium Metal Batteries

Polyfluorinated Crosslinker-Based Solid Polymer Electrolytes for Long-Cycling 4.5V Lithium Metal Batteries

Ameliorating the interfacial issues of all-solid-state lithium metal batteries by constructing polymer/inorganic composite electrolyte

Optimal Interfacial Model between the Alloy Surface and Electrolyte Solvation Structure for a Stable Lithium Metal Electrode

In-Situ Polymerized High-Voltage Solid-State Lithium Metal Batteries with Dual-Reinforced Stable Interfaces

Durable and Adjustable Interfacial Engineering of Polymeric Electrolytes for Both Stable Ni-Rich Cathodes and High-Energy Metal Anodes

In Situ Construction of Li3N-enriched Interface Enabling Ultra-Stable Solid-State LiNi0.8Co0.1Mn0.1O2/lithium Metal Batteries