Abstract:Organic Lewis bases [2,2'-bipyridine (BPY), 4-hydroxy-1,5-naphthyridine-3-carbonitrile (DQCN), and thenoyltrifluoroacetone (TTFA)] with bi-coordination sites of N and O were employed as perovskite surface defect passivants to address the efficiency and stability issues of perovskite solar cells (PSCs), with typical phenethylammonium iodide (PEAI) and piperazinium iodide (PI) passivants as reference. The surface properties of the perovskite films before and after passivation were characterized by Fourier-transform infrared, ultraviolet-visible, photoluminescence (PL), and time-resolved PL spectroscopy, X-ray diffraction, ultraviolet photoelectron spectroscopy, scanning electron microscopy, and atomic force microscopy. The characterizations reveal that BPY, DQCN, or TTFA forms coordination bonds with exposed "Pb2+", leading to a slight decrease in the highest occupied molecular orbital or lowest unoccupied molecular orbital energy level and bandgap. These passivants (especially TTFA) can passivate the perovskite surface defects to inhibit non-radiative recombination while having almost no influence on the grain size and surface morphology. Utilizing the passivated perovskite as the light absorption layer, solar cells with an inverted configuration of indium tin oxide/NiO x /passivated MAPbCl x I3-x /C60/BCP/Ag have been fabricated, and power conversion efficiencies of 19.22, 17.85, 16.49, 16.31, and 17.88% have been achieved from PEAI, PI, BPY, DQCN, and TTFA, respectively. All the device performance based on passivated perovskite is superior to that of the control (15.75%) owing to the reduced carrier recombination. The device from TTFA exhibits almost comparable efficiency to that of PEAI and PI controls, indicating that TTFA has an equal excellent passivation effect to state-of-the-art PEAI and PI. Furthermore, the devices based on BPY, DQCN, and TTFA show superior long-term stability with an efficiency loss of only 13.2, 16.7, and 12.9%, respectively, after being stored for 40 days in a ∼12% humidity, low-oxygen level environment, which is 45.4, 38.8, and 44.4% for the control, PEAI, and PI devices, respectively, primarily due to the improved hydrophobicity of the perovskite surface. Our results demonstrate that it is feasible to achieve high-efficiency and long-term-stable perovskite solar cells via selecting the appropriate molecules to passivate perovskite surface defects.

Aryl Diammonium Iodide Passivation for Efficient and Stable Hybrid Organ‐Inorganic Perovskite Solar Cells

Manipulating the Interfacial Dipole Toward High-Performance Perovskite Solar Cells Via Conjugated Organic Ammonium

Suppressing surface and interface recombination to afford efficient and stable inverted perovskite solar cells

Direct Surface Passivation of Perovskite Film by 4-Fluorophenethylammonium Iodide toward Stable and Efficient Perovskite Solar Cells

Effective Passivation with Size-Matched Alkyldiammonium Iodide for High-Performance Inverted Perovskite Solar Cells

Efficient and Stable Chemical Passivation on Perovskite Surface Via Bidentate Anchoring

Perovskite Surface Passivation Using Thiophene-Based Small Molecules for Efficient and Stable Solar Cells

Organic iodides in efficient and stable perovskite solar cells: strong surface passivation and interaction

Gas Molecule Assisted All-Inorganic Dual-Interface Passivation Strategy for High-Performance Perovskite Solar Cells

Surface Passivation with Diaminopropane Dihydroiodide for p‐i‐n Perovskite Solar Cells with Over 25% Efficiency

Introduction of Multifunctional Triphenylamino Derivatives at the Perovskite/HTL Interface To Promote Efficiency and Stability of Perovskite Solar Cells

Pyridine Derivatives’ Surface Passivation Enables Efficient and Stable Carbon-Based Perovskite Solar Cells

Enhancing the performance of perovskite solar cells through simple bilateral active site molecule assisted surface defect passivation

Dual Role of Rapid Transport and Efficient Passivation in Inverted Methylammonium‐Free Perovskite Solar Cells Utilizing a Self‐Assembled Porous Insulating Layer

Enhancing Performance and Stability of Perovskite Solar Cells through Surface Defect Passivation with Organic Bidentate Lewis Bases

Hexylammonium Iodide Derived Two-Dimensional Perovskite As Interfacial Passivation Layer in Efficient Two-Dimensional/Three-Dimensional Perovskite Solar Cells.

Interfacial Defect Passivation Effect of N -Methyl- N -(thien-2-ylmethyl)amine for Highly Effective Perovskite Solar Cells

Enhancing Perovskite Solar Cell Performance through Propylamine Hydroiodide Passivation

Poly(Ethylene Glycol) Diacrylate as the Passivation Layer for High-Performance Perovskite Solar Cells

Efficient Defect Passivation for Perovskite Solar Cells by Controlling the Electron Density Distribution of Donor‐π‐Acceptor Molecules

Effective Passivation with Self‐Organized Molecules for Perovskite Photovoltaics