Abstract:The high cracking susceptibility is the major barrier hindering the broad adoption of additive manufacturing (AM) in traditional non-weldable superalloys. It is particularly important to explore the role of elements during the AM processing and establish a new alloy design criterion. In this study, the effect of carbon, a critical element that influences the solidification and mechanical properties of superalloys, on the printability and mechanical properties of a typical non-weldable Inconel 738 (IN738) alloy processed by laser powder bed fusion (LPBF) was studied. Different from the limitation of low carbon content in traditional superalloy design, it was found that a moderate increase of carbon content from 0.11 wt% (alloy IN738LC) to 0.3 wt% (alloy IN738-0.3 C) and 0.6 wt % (alloy IN738-0.6 C) can produce crack-free LPBF samples in a wide range of processing parameters. The effect of carbon content on the microstructure, tensile properties and cracking susceptibility of the LPBF-printed alloys was evaluated. With the increase of carbon content, more granular monocarbides of no more than 200 nm in size form into a quasi-continuous or continuous network at the boundaries of cellular structures, while the low melting-point phases containing boron and gamma/gamma ' eutectics at cellular boundaries are significantly reduced. The susceptibility to solidification cracking and liquation cracking is substantially decreased owing to the reduced level of element segregation, elimination of initiation source for liquid films, and decrease of local strain con-centration. As a result, LPBF IN738-0.3 C and IN738-0.6 C show excellent ultimate tensile strength (1320 and 1598 MPa) and superior total elongation (14.7% and 9.0%), respectively. The results above demonstrate the different roles of carbon element in AM and the potential for designing AM non-weldable superalloys with improved printability and mechanical properties via alloy composition optimization.

Improvement in mechanical properties of Rene 104 superalloy during laser additive manufacturing process

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Pre-softening HIP Treatment Enabled Crack-Healing and Superior Mechanical Properties for René 142 Superalloy Fabricated Via Laser Powder Bed Fusion

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

A review of laser additive manufacturing (LAM) aluminum alloys: Methods, microstructures and mechanical properties

Influence of Scanning Strategy and Post-Treatment on Cracks and Mechanical Properties of Selective-Laser-Melted K438 Superalloy

Selective laser melting of the hard-to-weld IN738LC superalloy: Efforts to mitigate defects and the resultant microstructural and mechanical properties

Cracking inhibition of nano-TiC reinforced René 104 superalloy fabricated by selective laser melting

Effects of Processing Parameters on a Β-Solidifying TiAl Alloy Fabricated by Laser-Based Additive Manufacturing

Microstructure and Mechanical Properties of an Ultra-High Strength Steel Fabricated by Laser Hybrid Additive Manufacturing

Effect of heat treatments on the microstructure and mechanical properties of Ren?e 104 superalloy manufactured by selective laser melting

Effect of high preheating on the microstructure and mechanical properties of high gamma prime Ni-based superalloy manufactured by laser powder bed fusion

Effect of Carbon Content on the Microstructure, Tensile Properties and Cracking Susceptibility of IN738 Superalloy Processed by Laser Powder Bed Fusion

Oxidation Behavior and Control Method in Laser Solid Forming of Rene 104 Superalloy

Relationship Between Process Parameters and Defects in Laser Powder Bed Fusion Additive Manufacturing of Crack-Sensitive Al–Cu–Mg Alloy

Reducing cracking sensitivity of CM247LC processed via laser powder bed fusion through composition modification

Defect-healing of a Laser-Powder Bed Fusion Ti6Al4V Alloy Via Electro-Assisted Micro-Forging

The Effect of Laser Remelting on the Microstructure and Mechanical Properties of the Bonding Interface in a Hybrid Metal Additive Manufacturing Process

Study of the Crack and Porosity Regulation of a Non-weldable Ni-Based Superalloy Fabricated by Laser Powder Bed Fusion

Effect of ultrasonic shot peening on microstructure and mechanical properties of GH3230 superalloy during selective laser melt solution heat treatment

Experimental Study of Forming Rene95 Alloy Parts by Laser Cladding