Abstract:In the injection molding field, the flow of plastic material is one of the most important issues, especially regarding the ability of melted plastic to fill the thin walls of products. To improve the melt flow length, a high mold temperature was applied with pre-heating of the cavity surface. In this paper, we present our research on the injection molding process with pre-heating by external gas-assisted mold temperature control. After this, we observed an improvement in the melt flow length into thin-walled products due to the high mold temperature during the filling step. In addition, to develop the heating efficiency, a flow focusing device (FFD) was applied and verified. The simulations and experiments were carried out within an air temperature of 400 °C and heating time of 20 s to investigate a flow focusing device to assist with external gas-assisted mold temperature control (Ex-GMTC), with the application of various FFD types for the temperature distribution of the insert plate. The heating process was applied for a simple insert model with dimensions of 50 mm × 50 mm × 2 mm, in order to verify the influence of the FFD geometry on the heating result. After that, Ex-GMTC with the assistance of FFD was carried out for a mold-reading process, and the FFD influence was estimated by the mold heating result and the improvement of the melt flow length using acrylonitrile butadiene styrene (ABS). The results show that the air sprue gap (h) significantly affects the temperature of the insert and an air sprue gap of 3 mm gives the best heating rate, with the highest temperature being 321.2 °C. Likewise, the actual results show that the height of the flow focusing device (V) also influences the temperature of the insert plate and that a 5 mm high FFD gives the best results with a maximum temperature of 332.3 °C. Moreover, the heating efficiency when using FFD is always higher than without FFD. After examining the effect of FFD, its application was considered, in order to improve the melt flow length in injection molding, which increased from 38.6 to 170 mm, while the balance of the melt filling was also clearly improved.

Flowing of External Melt from the Nozzle in the Forming Process of FDM

Numerical simulation of filling flow of polymer melt in injection molding

Interfacial Bonding During Multi-Material Fused Deposition Modeling (FDM) Process Due to Inter-Molecular Diffusion

Modeling of Bond Formation Between Polymer Filaments in the Fused Deposition Modeling Process

Numerical Simulation of Flow-Induced Stresses in Mold Filling Process Using a Three-Dimensional Two-Phase Flow Model

Quantitative Analysis of Surface Profile in Fused Deposition Modelling

Modelling and simulation of moving interfaces in gas-assisted injection moulding process

INTEGRATED SIMULATION OF MELT FLOW, FIBER FRACTURE AND FIBER ORIENTATION FOR FIBER REINFORCED PLASTICS IN INJECTION MOLDING

New Approach to Develop a 3D Non-Isothermal Computational Framework for Injection Molding Process Based on Level Set Method

Three-dimensional Simulations of Non-Isothermal Transient Flow and Flow-Induced Stresses During the Viscoelastic Fluid Filling Process

Surface Model Based Modeling and Simulation of Filling Process in Gas-Assisted Injection Molding

Study on External Gas-Assisted Mold Temperature Control with the Assistance of a Flow Focusing Device in the Injection Molding Process

Thermo-Fluid-Dynamic Modeling of the Melt Pool During Selective Laser Melting for AZ91D Magnesium Alloy

Numerical Simulation of Melt Filling and Gas Penetration in Gas Assisted Injection Molding

Dimensional Analysis Theory and Molecular Dynamics Simulation of Polypropylene Melt Flow during Injection Molding Process

Simulation of filling process in gas-assisted injection molding by using surface model

Gas assisted fused deposition modeling: effects of assist gas parameters on print quality and properties

The Adhesive Mechanism and Thermal Analysis of Fibers in the FDM Process

3D Non-Newtonian deposition flow and thermal simulations to evaluate the scale-up potential for material extrusion of single walled ABS parts with overhang

Insights into Temperature Simulation and Validation of Fused Deposition Modeling Processes

A Transient Updated Lagrangian Finite Element Formulation for Bond Formation in Fused Deposition Modeling Process