Abstract:As a metallurgical and chemical raw material, electrolytic manganese is an important strategic resource. However, with the rapid development of the electrolytic manganese industry, the correct disposal of anode slime has become a serious problem. The purpose of this experiment was to reduce the occupation of land resources by the lead–containing waste residue of electrolytic manganese, reduce the pollution caused by the lead–containing waste residue to the environment and provide a reference for the research on the treatment technology and resource utilization of lead–containing waste residue in China. In this experiment, a special process was studied for the composition characteristics of lead–containing waste residues produced by electrolytic manganese. The acid leaching–enrichment–membrane electrolysis process was used to recover the lead in the lead–containing waste residues of electrolytic manganese and to recover the acid, so as to maximize the utilization of resources. In this experiment, the pretreated lead–containing waste residue was leached, enriched and concentrated, and then the enriched Pb2+ solution was used as cathode solution and dilute nitric acid as anode solution to recover lead by membrane electrolysis. The membrane electrolysis experiment uses lead plate as cathode, selects the best anion exchange membrane and anodic electrolysis material, and then takes lead recovery, acid recovery, current efficiency, voltage and power consumption as investigation indexes to explore and analyze the influence of many factors such as Pb2+ concentration and current density on the experiment, so as to determine the best membrane electrolysis process parameters. The optimum process parameters of lead recovery by membrane electrolysis were determined as follows: Pb2+ concentration was 40 g/L, current density was 30 mA/cm2, reaction temperature was 60 °C, cathodic pH value was 4.0, anodic HNO3 concentration was 0.5 mol/L, and cathodic ammonium nitrate concentration was 50 g/L. Under the optimal conditions, the current efficiency was 85.6%, the acid recovery was 73.03%, the lead recovery was 99.2%, the voltage was 3.8 V, and the power consumption was 1148.4 kW·h·t−1. Through the three steps of acid leaching–enrichment–membrane electrolysis, 78.53% of the Pb2+ in the original lead–containing waste residue can be recovered in the form of metal lead element, and the HNO3 recovered in the anode chamber can also be used again in the acid leaching process, which can not only solve the problem of environmental pollution caused by lead–containing waste residue but also achieve the recovery and utilization of resources, with good social and economic benefits.

Recovery of Lead and Silver from Lead-Bearing Wastes Using Reducing--matting Smelting Process

Pyrometallurgical Recovery of Valuable Metals from Flue Dusts of Copper Smelter Through Lead Alloy

Recovery of Zinc and Copper from Lead Slag by the Combined Process of Beneficiation and Roasting

Probing Study on Separating Pb, Zn, and Fe from Lead Slag by Coal-based Direct Reduction

Phase Evolution and Recovery Rate of Sb in Lead–Silver Slag Treated via Melting–Fuming Method

Utilization and detoxification of gypsum sludge by replacing limestone in reduction smelting of high lead slag

Sb recovery from an As pre-removed lead anode slime using a ZnS-Na2CO3 smelting reduction

Recovery of Copper, Lead and Zinc from Copper Flash Converting Slag by the Sulfurization-Reduction Process

Enrichment of valuable metals from silver tailings using the alkali roasting-leaching method

An integrated and sustainable hydrometallurgical process for enrichment of precious metals and selective separation of copper, zinc, and lead from a roasted sand

Recovery of lead from lead paste in spent lead acid battery by hydrometallurgical desulfurization and vacuum thermal reduction

Recyclable Recovery of Lead from Zinc Hydrometallurgy Residue: By NH 4 Cl-MgCl 2 Leaching and Novel Cyclone-Electrowinning

The hair-peg organs of the shore crab, Carcinus maenas (Crustacea, Decapoda): Ultrastructure and functional properties of sensilla sensitive to changes in seawater concentration

An Innovative Process for the Direct Recovery of Lead from Waste Lead Paste

Treating waste with waste: Metals recovery from electroplating sludge using spent cathode carbon combustion dust and copper refining slag

Chemical-Free Method for Recovery of Lead from Spent Lead Paste by Reductive Sulfation Technique from By-product Utilization

Lead Recovery from a Lead Concentrate throughout Direct Smelting Reduction Process with Mixtures of Na2CO3 and SiC to 1000 °C

Recovery of lead and silver from zinc acid-leaching residue via a sulfation roasting and oxygen-rich chlorination leaching method

Recovery and Utilization of Lead in Lead–Containing Waste Residue from Electrolytic Manganese Production

Efficient Desulfurizer Recycling during Spent Lead–Acid Batteries Paste Disposal by Zero‐Carbon Precursor Hypothermic Smelting

Molten salt mediated low-temperature direct roasting of spent lead paste