Abstract:The solubility of a NiO cathode in molten carbonate fuel cell (MCFC) electrolyte is one of the major technical obstacles to the commercialization of such a fuel cell. LiFeO2 has been selected as a candidate cathode material for MCFC because its solubility is very small and the rate of dissolution into the melt is slower than that for NiO. However, the electrical conductivity of pure LiFeO2 is lower than that of NiO. Thus a novel cathode for MCFC was prepared by coating nanometer LiFeO2 grains on the surface of a porous NiO cathode using a simple combustion process. X-ray diffraction (XRD), energy dispersive X-ray analysis (EDAX) and scanning electron microscopy (SEM) were employed in the cathode characterization. As can be detected by XRD and EDAX, the LiFeO2 coating on the surfaces of the modified NiO cathodes increased with increase in the pre-treatment times. SEM observation shows that the coating consisted of nanometer LiFeO2 grains that were tightly sintered with the NiO particles. Due to its excellent stability in carbonate melts under the standard conditions of an MCFC cathode, the LiFeO2 coating significantly retarded the dissolution of the inner NiO in either eutectic Li–K or Li–Na carbonate melts. The measurements of the electrical conductivity show that, although the pure LiFeO2 has a much lower electrical conductivity in comparison with the NiO(Li), the electrical conductivity of LiFeO2 coated NiO was similar to that of NiO(Li) after being immersed and lithiated in Li–K carbonates. In this work, the tests of the unit cells show that the LiFeO2 coated NiO cathode had a better performance than the NiO cathode.

Stability Analysis of Cathode Materials in Molten Carbonate Fuel Cells

Thermodynamic Stability Assessment of MIEC Cathode Materials for Solid Oxide Fuel Cells

Electrochemical Characterization of La0.8Sr0.2MnO3-coated NiO As Cathodes for Molten Carbonate Fuel Cells

Stability of Ce0.8Sm0.2O2 Electrolyte and Mn1.5CO1.5O4 for Solid Oxide Fuel Cells

Performance and optimization of perovskite-type La1·4Ca0·6CoMnO5+δ cathode for intermediate-temperature solid oxide fuel cells

Stability of Nio Cathode Modified by Zno Additive for Molten Carbonate Fuel Cell

A Highly Stable Cobalt-Free Laba0.5sr0.5fe2o6-Delta Oxide As A High Performance Cathode Material For Solid Oxide Fuel Cells

Preparation and Properties of Fe-Based Double Perovskite Oxide as Cathode Material for Intermediate-Temperature Solid Oxide Fuel Cell

La-doped Ba0.5Sr0.5Co0.8Fe0.2O3- D As Cathode for Protonic-Conducting Solid Oxide Fuel Cells with Enhanced Structure Stability

Electrical and Stability Performance of Anode-Supported Solid Oxide Fuel Cells with Strontium- and Magnesium-Doped Lanthanum Gallate Thin Electrolyte

Evaluation of Ca 3 (co,m) 2 O 6 (m=co, Fe, Mn, Ni) As New Cathode Materials for Solid-Oxide Fuel Cells

Insights Into The Co2 Stability-Performance Trade-Off Of Antimony-Doped Srfeo3-Delta Perovskite Cathode For Solid Oxide Fuel Cells

A highly stable cobalt-free LaBa0.5Sr0.5Fe2O6-δ oxide as a high performance cathode material for solid oxide fuel cells

Self-stabilized Hybrid Cathode for Solid Oxide Fuel Cell: A-site Deficient Perovskite Coating As Solid Solution for Strontium Diffusion

A Novel Modified Nio Cathode for Molten Carbonate Fuel Cells

Phase Stability of Perovskite Oxide Electrodes under Operating Condition in Solid Oxide Fuel Cell

CO2-stable Alkaline-earth-free Solid Oxide Fuel Cells with Ni0.7Co0.3O-Ce0.8Sm0.2O1.9 Composite Cathodes

Valence Regulation of Ferrite Perovskite for High Performance Cobalt‐free Cathode of Solid Oxide Fuel Cell

Stability Investigation for Symmetric Solid Oxide Fuel Cell with La0.4Sr0.6Co0.2Fe0.7Nb0.1O3-δElectrode

A (la,sr)mno3 Nano-Film Embedded into (ba,sr)(co,fe)o3 Porous Cathode for Stability Enhancement

Development of La0.6Sr0.4Co0.2Fe0.8O3−δ Cathode with an Improved Stability Via La0.8Sr0.2MnO3-film Impregnation