Abstract:This paper proposes a bulk micromachined bandpass filter on 0.5mm-thick Pyrex glass, whose operation is based on the splitting of the odd and even degenerate mode in a dual-mode resonator, with the addition of a perturbation element. In such a way, a filter may require only half resonators of a traditional one, resulting in a more compact configuration over those ever reported. A 4%-bandwidth bandpass filter centered at 17GHz was designed. The square-ring-like coplanar waveguide (CPW) act as a dual-mode resonator, and an open-circuited stub attached to the inner corner of the square-ring acts as the perturbation element and dominates the filter bandwidth. The two bulk-micromachined switches for tuning are placed symmetrically along the diagonal line. Since the electrical length of CPW is extended after being loaded by capacitive switches, both the degenerate resonating frequencies and the filter mid-band frequency are shifted downward. Theoretical formulas are derived for various actuation states of all the switches. The filter performance is analysed also using finite-element fullwave tools. A frequency shift of 0.6GHz is seen which is close to 0.58GHz obtained from analytical solutions. Both the original and tuned state come with satisfying microwave performance, i.e. low passband insertion-loss (< 0.5dB) and return-loss (< −15dB) and high stopband rejection. It is also shown that the simulated result is in good agreement with theoretical solutions. The bulk microfabrication is shown to be much simpler than surface micromachining conventionally used for RF MEMS switches. Since the bridge skeleton is Si, thermal mismatch between all-metal bridge and dielectric substrate is avoided, and reliability at elevated temperature is guaranteed or at least greatly improved. Besides, the p++ doped Si line patterned simultaneously with the microbridges, can also be used as a DC biasing resistor, which can eliminate the additional steps to fabricate the resistive alloy line. The tested results of the fabricated switch samples are also shown. The device may be a good candidate for novel Ku-band inter-scientific satellite communication or wireless networking.

A Silicon-Based Self-Shielded MEMS Bandpass Filter

A Novel 76 and 94ghz Dual Band Bandpass Filter Using Multilayer Step Impedance Resonators (Sirs)

Design of a Miniaturized Dual-Band Double-Folded Substrate Integrated Waveguide Bandpass Filter with Controllable Bandwidths

Design Of Ku-Band Sir Interdigital Bandpass Filter Using Silicon-Based Micromachining Technology

3D Heterogenous Integrated Wideband Switchable Bandpass Filter Bank for Millimeter Wave Applications

Novel Bandpass Filters by Using Cavity-Loaded Dielectric Resonators in A Substrate Integrated Waveguide

A New Wide Stopband Microstrip Bandpass Filter with Miniaturized Interdigital Capacitor Resonator

A Novel Surface-Mounted Monoblock Dielectric Filter

Miniaturized Dual-Band Substrate Integrated Waveguide Filter with Controllable Bandwidths

A triple-mode ring dielectric resonator band-pass filter using substrate integrated waveguide (SIW)

Design and Fabrication of a MEMS Bandpass Filter with Different Center Frequency of 8.5-12 GHz.

A Novel Compact Thru-Silicon-Via On-Chip Passive Mmw Bandpass Filter for 77ghz Applications

Bandwidth and Wavelength Tunable Optical Passband Filter Based on Silicon Multiple Microring Resonators.

Design and Optimization of an S-Band MEMS Bandpass Filter Based on Aggressive Space Mapping

A Miniaturized C-B and SIW Bandpass Filter based on LTCC

Miniaturized millimeter-wave dual-band band-pass on-chip filter in 0.13-μm SiGe BiCMOS

Micromachined W-Band Waveguide Duplexer Design Based on MEMS Technology

Dual-Passband SAW Filter Based on a 32°Yx-Ln/sio2/sic Multilayered Substrate.

Microelectromechanical filters for signal processing

A Bulk Micromachined Tunable Dual-Mode Microwave Bandpass Filter on Coplanar Waveguide

Design of a RF MEMS Passive LC Filter