Abstract:Bar buckling and subsequently low-cycle fatigue fracture is one of the main failure modes of RC columns/piers under strong earthquakes. Due to the adoption of new metallurgical technology and possibly enduring higher stress, high-strength steel bars (HSSB) may be more prone to occur buckling and low-cycle fatigue failure, which will detrimentally affect the seismic performance of RC columns/piers. In view of this, this paper studies the buckling and low-cycle fatigue performance of high-strength steel bars (HSSB) HTRB600 and compares with normal steel bars (NSB) HRB400E. At first, the monotonic tensile and compressive tests of HTRB600 and HRB400E steel bars with different slenderness ratios (L/D = 6, 8, 10, 12, 15) were conducted to study their monotonic tensile and compressive properties. Then, the low-cycle fatigue tests of HTRB600 and HRB400E reinforcing steel with different strain amplitudes and slenderness ratios were conducted to evaluate their low-cycle fatigue performance. The fatigue life prediction formulas for HTRB600 and HRB400E steel bars taking into account the effects of inelastic buckling were proposed through the regression analysis of test results. Moreover, the fractured surfaces obtained by the scanning electron microscope (SEM) were used to compare the low-cycle fatigue failure features of HTRB600 and HRB400E steel bars. Finally, a finite element model (FEM) was developed to simulate the nonlinear mechanical behaviors of HTRB600 and HRB400E steel bars under monotonic and cyclic loading. Test results show that HTRB600 steel bars present lower tensile ductility, more severe post-buckling softening and pinching effect than HRB400E steel bars. The increase in yield strength, buckling length and strain amplitude will reduce the low-cycle fatigue life of steel bars. The range of striation marks observed from low-cycle fatigue fractured surfaces by SEM for HTRB600 steel bar is smaller than HRB400E steel. The calibrated buckling and low-cycle fatigue parameters by the validated finite element model (FEM) can be adopted to accurately simulate the inelastic seismic response of RC structures.

RESEARCH ON BUCKLING STATE DETERMINATION OF REINFORCING BARS BASED ON LATERAL DEFLECTION

LATERAL-TORSIONAL BUCKLING OF C-SECTION COLD-FORMED PURLINS WITH TWO ANTI-SAG BARS

Critical Load for Shear-Induced Lateral-Distortional Buckling in I-section Steel Beams Considering Flexural Stiffness Ratio

Lateral Buckling of C-section Purlins with One Anti-Sag Bar at Middle Span Section

RESEARCH ON FLEXURAL PERFORMANCE OF DOUBLE-STEEL REINFORCED CONCRETE BEAM

Experimental Investigation into Flexural Buckling of Double-Limb Built-Up Plate Members under Compression

Modelling for Compressive Buckling of Reinforcing Bars

Experiment Investigation of the Influence of Reinforcing Bar Buckling on Seismic Behavior of RC Columns

Investigation on low-cycle fatigue performance of high-strength steel bars including the effect of inelastic buckling

LATERAL BUCKLING ELASTIC SOLUTION OF STEEL-CONCRETE COMPOSITE BEAMS ACTED ON ITS ENDS WITH AN EQUAL CONSTANT BENDING MOMENT

Effect of Circumferentially Nonuniform Lateral Tension on Bond Behavior Between Plain Round Bars and Concrete: Analytical Study

Lateral Buckling Analysis of the Steel-Concrete Composite Beams in Negative Moment Region

Local Buckling of Rectangular Concrete-Filled Steel Tubular Columns with Binding Bars under Eccentric Compression

EXPERIMENTAL RESEARCH ON THE BUCKLING BEHAVIOR OF HRB600 STEEL BARS

Improved Nonlinear Cyclic Stress–Strain Model for Reinforcing Bars Including Buckling Effect and Experimental Verification

Local Buckling Tests on Cold-Formed Steel Beams

Experimental and Analytical Studies on Elastic-Plastic Local Buckling Behavior of Steel Material under Complex Cyclic Loading Paths

Elastic Distortional Buckling Analysis of Steel-Concrete Composite Beams in Negative Moment Region

Modeling of Buckled Reinforcing Bars Including Effect of Lateral Expansion of Concrete Core

Experimental study on local buckling behavior of composite walls with double steel plates and filled concrete

EXPERIMENTAL STUDY ON COMPRESSION BEHAVIOR OF FRP TUBE BULGING-RESTRAINED REBAR