Abstract:Two series of uniaxial tensile tests are performed on isotactic polypropylene with the strain rates ranging from 5 to 200mm/min. In the first series, injection-molded specimens are used without thermal pre-treatment. In the other series of experiments, the samples are annealed for 51h at 160°C prior to testing.A constitutive model is developed for the viscoplastic behavior of isotactic polypropylene at finite strains. A semicrystalline polymer is treated as equivalent heterogeneous network of chains bridged by permanent junctions (physical cross-links and entanglements). The network is thought of as an ensemble of meso-regions connected with each other by links (lamellar blocks). In the sub-yield region of deformations, junctions between chains in meso-domains slide with respect to their reference positions (which reflects sliding of nodes in the amorphous phase and fine slip of lamellar blocks). Above the yield point, the sliding process is accompanied by displacements of meso-domains in the ensemble with respect to each other (which reflects coarse slip and fragmentation of lamellar blocks). To account for alignment of disintegrated lamellar blocks along the direction of maximal stresses (which is observed as strain-hardening of specimens in the post-yield regions of deformations) elastic moduli are assumed to depend on the principal invariants of the right Cauchy–Green tensor for the viscoplastic flow.Stress–strain relations for a semicrystalline polymer are derived by using the laws of thermodynamics. The constitutive equations are determined by five adjustable parameters that are found by matching observations. Fair agreement is demonstrated between the experimental data and the results of numerical simulation. A noticeable difference is revealed between the mechanical responses of non-annealed and annealed specimens: (i) necking of samples not subjected to thermal treatment precedes coarse slip and fragmentation of lamellar blocks, whereas cold-drawing of annealed specimens up to a longitudinal strain of 80% does not induce spatial heterogeneity of their deformation; (ii) the elastic modulus increases with the strain rate for non-annealed specimens and decreases for annealed samples.

Experimental Study on Mechanical Properties of PMMA under Unidirectional Tensile at Low and Intermediate Strain Rates

A constitutive model for poly-methyl-methacrylate over a wide range of strain rates and temperatures

Experimental Study of Mechanical Properties of CFRP under Different Strain Rates and Temperatures

A Constitutive Model for Strain Hardening Behavior of Predeformed Amorphous Polymers: Incorporating Dissipative Dynamics of Molecular Orientation

Shear-compression failure behavior of PMMA at different loading rates

Dynamic Tensile Behavior of Polyamide 6 at Different Strain Rates: Experiments and Constitutive Model

A Uniform Viscoelastic-Plastic Constitutive Model for MD-PMMA at a Wide Temperature Range

On-Demand Tailoring between Brittle and Ductile of Poly(methyl methacrylate) (PMMA) via High Temperature Stretching

Experimental Investigation and Modeling of the Mechanical Properties of Construction PMMA at Different Temperatures

Weibull Statistical Analysis on Tensile Strength of Adhesive Joint in PMMA

Modeling the Rate-Dependent Ductile-Brittle Transition in Amorphous Polymers

Experimental Study of Size Dependence of Fracture Toughness of PMMA

Rate-dependent Constitutive Model of Poly(ethylene Terephthalate) for Dynamic Analysis

Experimental and Modeling Study of the Compressive Behavior of PC/ABS at Low, Moderate and High Strain Rates

Deformation and failure maps for PMMA in uniaxial tension

High Strain-Rate Tensile Experiment on Polycarbonate Bar

A viscoelastoplastic constitutive model of semi-crystalline polymers under dynamic compressive loading: Application to PE and PA66

Dynamic compressive behavior and constitutive model of polyamide-6 at different temperatures and strain rates

Determining the constitutive behavior of nonlinear visco-elastic-plastic PMMA thin films using nanoindentation and finite element simulation

Experimental Study of Tensile Property of Cp-Ti at Intermediate Strain Rates

The effect of strain rate on the viscoplastic behavior of isotactic polypropylene at finite strains