Decoupled analysis of the effect of hydroxyl functional groups on delay of ignition with fictitious hydroxyl
Jialong Zhu,Ruina Li,Zhong Wang,Shuai Liu,Hui Lv
DOI: https://doi.org/10.1016/j.psep.2022.03.028
IF: 7.8
2022-05-01
Process Safety and Environmental Protection
Abstract:In this study, the spray characteristics of ether fuels have been studied numerically using a new hybrid spray model in KIVA4 CFD code which accounts for cavitation inside he injector nozzle holes. The cavitation phenomenon was investigated numerically using Fluent CFD software. The properties of ether fuels have been predicted and reported. It is found that ether fuels cavitates higher compared to diesel fuel which means high fuel quantity should be injected to achieve same power output as diesel fueled engine. The spray simulation shows the atomization of ether fuels are far superior to diesel as they are characterized by high Reynolds number and low Ohnesorge number.Fuel-rich combustion is a promising technique to produce hydrogen by reforming hydrocarbons. Predictive modeling of the fuel reforming process needs a reliable chemical mechanism which is usually validated using laminar flame speed (LFS) data. While LFSs have been extensively employed to optimize mechanisms under fuel-lean, stoichiometric, and slightly fuel-rich conditions, it remains a formidable challenge to measure the LFSs of very rich mixtures (e.g., equivalence ratio ϕ≥2) due to significant soot formation in such conditions, which leads to the LFS data under fuel-rich conditions being rather scarce. To overcome the challenge, a clear understanding of soot formation and its impact on LFS measurements is required. In this work, a series of one-dimensional outwardly propagating spherical flames (OPFs) with and without considering soot formation are simulated for rich ethylene/air mixtures (2.0≤ϕ≤3.5), in order to understand soot dynamics and morphology in the OPFs and to quantify the effects of soot formation on the determination of LFS using the OPF method under fuel-rich conditions. To this end, a detailed chemistry accounting for major pathways of PAH formation up to A7 (coronene, C24H12) is employed and coupled with a state-of-the-art soot model considering nucleation, condensation, coagulation, surface growth, oxidation, and fragmentation. It is found that soot dynamics and morphology are very sensitive to the change in equivalence ratio and flame radius. Specifically, surface growth and oxidation play a dominant role in soot formation/evolution and can balance each other at ϕ=2.0, resulting in limited soot formation. However, the PAH-based condensation can dominate over other processes at ϕ≥2.5 and hence a large amount of soot is observed. Moreover, the maximum value of primary particle diameters would tend to a constant as the flame radius increases. The results also show that the ratio between total soot mass and the mass of burned gas, msoot/mburned, follows an exponential law given by msoot/mburned=100.47ϕ−3.76, implying that soot formation can be exponentially enhanced by increasing equivalence ratio. Furthermore, it is found that under very rich conditions, the presence of soot has a significant impact on the determination of LFS, which leads to the measured LFS at ϕ=3.5 being 22% lower than 1D planar adiabatic flame speed. This is mainly attributed to the thermal and flow effects of soot radiation, i.e., the reduction of flame temperature and negative flow speed of the burned gas. The above findings suggest that the impact of soot radiation should be carefully treated when determining the LFSs of rich premixed mixtures at ϕ≥2.0.The two-stage injection processes of three fatty acid esters, methyl laurate, methyl oleate and ethyl oleate, were investigated and compared with that of fossil diesel using a high-pressure diesel engine common rail injection system. The injection characteristics studied included injector inlet pressure characteristics, and rate and quantity of fuel mass injected per cycle. The effects of fuel properties and injection dwell time between the pilot and main injection events were also considered. Differences in the fuel properties of diesel and fatty acid esters caused modest changes in the main injection quantities and fuel pressure fluctuation characteristics after the end of injection, and the changes were affected by different injection pressures. The injection dwell time was also found to influence the injector inlet pressure characteristics at the start of the main injection event and thus the amount of fuel injected during main injection was slightly changed.The mean local reaction rate related to the average expansion across the front and computed from the mean ve -Abstract Truncated-
engineering, environmental, chemical