Abstract:Objective: To analyze the hip joint biomechanics of the acetabular anatomical reconstruction and nonanatomical reconstruction in total hip arthroplasty (THA) for Crowe type Ⅲ developmental dysplasia of the hip (DDH) by finite element method, which provided theoretical foundation and experimental basis for the anatomical acetabular reconstruction during THA in clinical practice. Methods: One patient with left end-stage hip arthritis secondary to Crowe type Ⅲ DDH was selected in this study, who underwent total hip arthroplasty in the orthopedic department of the First Affiliated Hospital of Bengbu Medical College in April 2020. This patient was female, 57 years old. The preoperative and postoperative three dimentional CT scan of the patient's pelvis were performed. Fourteen acetabular cup models with different anteversion, inclination and rotation center height were established in Mimics and 3-Matic software. The boundary and load conditions were set in Abaqus software. The Von Mises and stress distribution of the hip joint were calculated and observed. Results: In the Crowe type Ⅲ DDH THA, if the hip rotation center was restored anatomically and the acetabular cup's inclination was set as 40°, the cup's anteversion varied from 5° to 25°, the lowest Von Mises value of acetabular cup and polyethylene liner occured in 20°anteversioin;if the hip rotation center was restored anatomically and the acetabular cup's anteversion was set as 15°, the cup's inclination varied from 35° to 55°, the lowest Von Mises value of acetabular cup and polyethylene liner occured in 35° inclination;if the acetabular cup's anteversion and inclination were set as 15°and 40°respectively, the up migration of hip rotaion center varied from 0 mm to 20 mm, the lowest Von Mises value of acetabular cup and polyethylene liner occured in 10 mm up migration. In all fourteen models, the Von Mises value of the acetabulum, acetabulum cup and polyethylene liner were lowest when the acetabular cup's anteversion and inlcination were 15°, 35° respectively, as well as the rotation center was restored anatomically. Conclusion: In total hip arthroplasty for Crowe type Ⅲ DDH, the anatomical restoration of hip rotation center with 15° anteversion and 35° inclination of the acetabular cup are suggested, bone graft above the acetabular cup and additional screws are recommended simultaneously to further reduce the Von Mises of hip joint.

Characteristics of acetabular bony cyst in patients with developmental dysplasia of the hip

Morphological characteristics of developmental dysplasia of the hip: Three-dimensional CT evaluation

[Combination Surface Shaded Display with Multiplanar Reconstruction in the Evaluation of Acetabular Morphologies in Patients with Developmental Dysplasia of the Hip Before Total Hip Arthroplasty].

Acetabular reconstruction of total hip arthroplasty for development dysplasia hip

Acetabular Reconstruction of Total Hip Replacement in the Treatment of Dysplastic Hip

The Diagnosis and Therapeutics of the Juxta-Articular Bone Cyst in the Acetabulum

Acetabulum morphology in osteoarthritis secondary to Crowe II developmental dysplasia of the hip, a CT study

Anatomic placement of the acetabulum improves the survival rate in patients with Crowe type-II dysplasia undergoing total hip arthroplasty

Anatomic hip center reconstruction during total hip arthroplasty for severe osteoarthritis secondary to hip dysplasia

Total Hip Arthroplasty in Patients with Crowe III/IV Developmental Dysplasia of the Hip: Acetabular Morphology and Reconstruction Techniques

[Total Hip Arthroplasty with Uncemented Cup and Femoral Head Autografts for Coxarthrosis Due to Dysplasia].

Anatomic Placement of the Acetabulum Improves the Survival Rate in Patients with Crowe Type-Ii Dysplasia Undergoing Total Hip Arthroplasty.

Correlation between the acetabular component loosing rate of bone-cement total hip replacement and the severity of the development dysplasia of the hip

Morphological Analysis of True Acetabulum in Hip Dysplasia (crowe Classes I-IV) Via 3-D Implantation Simulation

Acetabular Diameter Assessment and Three-Dimensional Simulation for Acetabular Reconstruction in Dysplastic Hips

[Acetabular Morphological Analysis in Patients with High Dislocated DDH Using Three-Dimensional Surface Reconstruction Technique].

Surgical treatment for developmental dysplasia of hip in older children

Cementless Acetabular Component with or Without Upward Placement in Dysplasia Hip: Early Results from a Prospective, Randomised Study

Central Acetabular Osteophytes (CAO) Are More Prevalent in the Borderline Developmental Dysplastic Hip (BDDH) Patients: a Propensity-Score Matched CT Study

Analysis of acetabular morphological pathology types in developmental dysplasia of the hip in children

[Hip joint biomechanical analysis of the acetabular anatomical reconstruction and nonanatomical reconstruction in total hip arthroplasty for Crowe type Ⅲ developmental dysplasia of the hip by finite element method]