Abstract:Experimental, analytical and numerical methods have been employed to study the aerodynamic performance of four different cooled tips with coolant mass ratios between zero and 1.2% at three tip gaps of 1%, 1.6% and 2.2% of the chord. The four cooled tips are two flat tips with different coolant holes, a cooled suction side squealer tip and a cooled cavity tip. Each tip has ten coolant holes with the same diameter.The uncooled cavity tip produces the smallest loss among all uncooled tips. On the cooled flat tip, the coolant is injected normally into the tip gap and mixes directly with flow inside the tip gap. The momentum exchange between the coolant and the flow that enters the tip gap creates significant blockage. As the coolant mass flow ratio increases, the tip leakage loss of the cooled flat tip first decreases and then increases. For the cooled cavity tip, the blockage effect of the coolant is not as big as that on the cooled flat tip. This is because after the coolant exits the coolant holes, it mixes with flow in the cavity first, and then mixes with tip flow in the tip gap. The tip leakage loss of the cooled cavity tip increases as the coolant mass flow ratio increase. As a result, at a tip gap of 1.6% of the chord, the cooled cavity tip gives the lowest loss.At the smallest tip gap of 1% of the chord, the cooled flat tip produces less loss than the cooled cavity tip when the coolant mass flow ratios larger than 0.23%. This is because with the same coolant mass flow ratio, a proportionally larger blockage is created at the smallest tip gap. At the largest tip gap of 2.2% of the chord, the cavity tip achieves the best aerodynamic performance. This is because, the effect of the coolant is reduced and the benefits of the cavity tip geometry dominate. At a coolant mass flow ratio of 0.55%, the cooled flat tips produce a lower loss than the cavity tip at tip gaps less than 1.3% of the chord. The cooled cavity tip produces the least loss for tip gaps larger than 1.3% of the chord. The cooled suction side squealer has the worst aerodynamic performance for all tip gaps studied.

Analysis of tip leakage vortex of different blade in ducted propeller

Numerical Study of Tip Leakage Vortex Around a NACA0009 Hydrofoil

Theoretical Prediction Model of Tip Leakage Vortex in a Mixed Flow Pump With Tip Clearance

Numerical and experimental study of tip leakage vortex structures and dynamics in a mixed-flow waterjet pump

Flow physics and loss mechanisms of tip leakage flow in variable-blade-pitch-angle ducted fans

Spatial–Temporal Evolution of Tip Leakage Vortex in a Mixed-Flow Pump With Tip Clearance

Analysis of Influential Factors to Tip Leakage Mixing Loss

Blade Aerodynamic Force and Tip Region Vortex Spatial-temporal Evolution Study of a Compressor Cascade

Numerical Study of Porous Tip Treatment in Suppressing Tip Clearance Vortices in Cavitating Flow

Experimental and Numerical Investigation on the Tip Leakage Vortex Cavitation in an Axial Flow Pump with Different Tip Clearances

Analysis of the relationship between turbulence characteristics and loss mechanism in the tip leakage flow of turbine blade

Large-eddy simulation of three-dimensional aerofoil tip-gap flow

Direct numerical simulation of a tip-leakage flow in a planar duct with a longitudinal slit

The Tip Leakage Flow of an Unshrouded High Pressure Turbine Blade with Tip Cooling

Basic Analysis Of Tip Leakage Mixing Loss

Examination on behavior of tip leakage flow in a three-stage gas-liquid two-phase flow pump

Effects of Clearance and Operating Conditions on Tip Leakage Vortex-Induced Energy Loss in an Axial-Flow Pump Using Entropy Production Method

Tip Leakage Vortex Trajectory and Dynamics in a Multiphase Pump at Off-Design Condition

Aerodynamic performance of tip leakage flow of two different blade tips in transonic turbine

Effects of tip clearance size on vortical structures and turbulence statistics in tip-leakage flows: A direct numerical simulation study

Aerodynamic Effects of an Incoming Vortex on Turbines with Different Tip Geometries