Abstract:Semisolid billet of the 7075 aluminum matrix composite reinforced with nano-sized SiC particles was first fabricated by an ultrasonic-assisted semisolid stirring method and rheoforming technology. Then it was thixoformed into a cylinder part under different remelting temperatures and soak times. The effects of the remelting temperature and soaking time on the mechanical properties and microstructure of the thixoformed composite part were investigated. The results show that parts of good quality were thixoformed successfully. The microstructure of the top side wall of the thixoformed part consisted of near spheroidal grains. A large quantity of elongated grains occurred in the medium and bottom side walls and the bottom itself. With increasing remelting temperatures, the size of the solid grains of the thixoformed parts showed a trend of first to increase and afterwards to decrease. High density dislocations were found in the microstructure when the remelting temperatures were 590 °C and 600 °C. When the soaking time was 15 min, the severest deformation occurred in the thixoformed part. High mechanical properties of the thixoformed parts were achieved under conditions such as a remelting temperature between 590 °C and 600 °C and a soaking time between 10 min and 15 min. The fracture mode of the thixoformed part changed from transgranular fracture to intergranular fracture when the remelting temperature was elevated from 580 °C to 610 °C. After the thixoformed parts were treated by T6, the ultimate tensile strength (UTS) and elongation of the side wall were improved to 552 MPa and 7.9%, respectively. Dispersed MgZn2 precipitates created by T6 heat treatment led to an improvement of the mechanical properties.

Ceramic Matrix Composite Thixoforming in Pseudo-semi-solid and Its Application to Satellite Angle-frames

Thixoforming of SiC ceramic matrix composites in pseudo-semi-solid state

Ceramics Matrix Composites Thixoforming in Pseudo-Semi-solid State and the Preliminary Experimental Study

Thixoforming of the satellite angel-frames in pseudo-semi-solid state and the primary experimental study

Al/SiCp Ceramic Matrix Composites Thixoforming in Pseudosemi-solid State

Ceramics matrix composites thixofroming in pseudo-semi-solid state

Manufacturing Titanium Metal Matrix Composites by Consolidating Matrix Coated Fibres

Feasibility of Al/Al_2O_3 Composite Thixoforming in Pseudo-semi-solid State

Novel MMC Microstructures Prepared by Melt Infiltration of Reticulated Ceramic Preforms

Thixo-die-forging of Al/Al2O3 Composite in Pseudo-Semi-solid State and Toughening-Strengthening

Pseudo-semi-solid Thixoforging of Cup Shell with Al/Al2O3

Study on Thxio-die-forging of 37%Al/Al_2O_3 Composite cup shell in Pseudo-semi-solid State

Thixo-die-forging of Al/Al_2O_3 composite in pseudo-semi-solid state

High volume fraction Al2O3/Al composite thixoforging in pseudo-semi-solid state

Rheological behavior of Al2O3n/Alμ composite in pseudo-semi-solid state

Influence of technological parameters on thixoforging of the composites in pseudo-semi-solid state

Effect of Remelting Temperature and Soaking Time on Microstructure and Mechanical Properties of the Thixoformed Part of Nano-Sized SiCp/7075 Composite

Research on Fabrication and Semisolid Processing of Semisolid Slurries of 7075 Aluminum Matrix Composites Reinforced with Nano-Sized SiC Particles

Preparation and properties of Al2O3/Al-2(1-0.2)Mg0.2Ti(1+0.2)O5 matrix ceramic composite

Influence of Technological Parameters on Thixoforging of the Compostitesin Pseudo-Semi-solid State