Abstract:Squeeze casting process can effectively resolve the casting difficulties for wrought aluminum alloys by pressurized solidification. The effects of applied pressure (0.1-125 MPa) on the microstructure refinement, non-equilibrium eutectic phase aggregation and fracture behavior of Al-Zn-Mg-Cu alloys prepared by squeeze casting were investigated through metallography, scanning electron microscopy and energy dispersive spectroscopy. The results showed that the primary α-Al grains transformed from coarse dendrites to refined equiaxed grains with increasing pressure. Considerable primary refinement was achieved at 100 MPa, with a significant decrease by 63% in the average grain size from 273 μm to 101 μm; the non-equilibrium eutectic phases were homogenized and refined, and almost dissolved into the Al matrix after T6 heat treatment. The mechanism of solidification behaviors in pressurized solidification was elucidated. Firstly, the applied pressure increased the thermodynamic driving force to promote primary grain nucleation. Secondly, the solute diffusion and constitutional undercooling at the front of the solid/liquid interface front were inhibited by pressure, and grain growth in a dendritic structure was thus restrained. Thirdly, interdependence theory and thermodynamic calculations were conducted to quantitatively describe the primary grain size changes under pressurized solidification. Lastly, the ternary eutectic reaction L → α-Al + T-Mg (Al, Zn, Cu) 2 + Al 2 Cu and binary eutectic reaction L→ α-Al + Al 7 Cu 2 Fe were suppressed by the reduced solute segregation. Furthermore, when the pressure increased from 0.1 MPa to 125 MPa, the ultimate tensile strength was raised from 428 MPa to 538 MPa, almost approaching that of samples by forging process. The refined eutectic phases decreased stress concentration and improved fracture behaviors.

Site Effectiveness of Thin-wall Aluminum-silicon Alloy Castings in Differential Pressure Casting Process

Determination of casting parameters of thick wall die-casting of magnesium alloy and simulation of its processing

Effect of Pressure and Mould Material on Density of Al-Si Alloy

Effects of different casting mould cooling rates on microstructure and properties of sand-cast Al-7.5Si-4Cu alloy

The Effect of Process Parameters on the Properties and Microstructure of A380 Aluminum Alloy Casting with Different Wall Thicknesses

Grain Refinement and Mechanical Properties Improvement of Casting A357 Alloy by High Pressure Differential Pressure Casting Process

Effects of Hollow Sand Mold on the Microstructure and Mechanical Properties of a Low Pressure Aluminum Alloy Casting

A Study of Thin-Walled ZL105A Casting Manufactured by Vacuum Differential Pressure Casting

Experimental Study on the Heat Transfer Behavior and Contact Pressure at the Casting-Mold Interface in Squeeze Casting of Aluminum Alloy

Development of Casting Process for Thin Walled Complex-Precision Aluminum Alloy Castings

Investigation on Effect of Counter Gravity Casting to Solidification Microstructure of High Strength Aluminum Alloys

Effect of Holding Pressure on Density and Cooling Rate of Cast Al-Si Alloy During Additive Pressure Casting

Effects of Casting Pressure on Microstructure and Mechanical Properties of Super Slow Speed Die Castings of ADC12 Aluminum Alloy

Semi-solid Isothermal Heat Treatment Microstructure Evolution of Die-casting Al-5Mg-2Si-Mn Alloy

Effects of cooling rates on microporosity in DC casting Al-Li alloy

Effect of Solidification Sequence on the Microstructure and Mechanical Properties of Die-Cast Al–11Si–2Cu–Fe Alloy

Microstructure and Mechanical Properties along Fluidity Length of Thin-Wall Aluminum Alloy under High Pressure Die Casting Conditions

Effects of Process Parameters on Internal Quality of Castings During Novel Casting

Effect of Cooling Rate on Microstructure and Mechanical Properties of Squeeze Cast Al–Cu–Mg Alloy

Effect of Gating System Design on the Quality of Aluminum Alloy Castings

Effect of pressure on the microstructure refinement, solidification mechanism and fracture behavior of wrought Al-Zn-Mg-Cu alloys prepared by squeeze casting