Abstract:The hot deformation behaviors of Fe–28Mn–10Al–1.5C–0.6V steel at T = 950–1150 °C and = 0.01–10 s −1 were studied using the Gleeble-3500 thermo-mechanical simulator. The constitutive model of Fe–28Mn–10Al–1.5C–0.6V steel was established by an artificial neural network (ANN) based on the experimental flow stress data. The critical conditions of dynamic recrystallization (DRX) of the steel under experimental conditions were studied by using both the Najafizadeh–Jonas work hardening rate model and the Cingara–McQueen rheological stress model. The true stress–true strain curve of the steel was analyzed, the work hardening rate was calculated, and the critical strain model was established. At the same time, the relevant material parameters were calculated by linear regression, and the DRX kinetics model of JMAK was also established. This model then was combined with the finite element software DEFORM-3D to simulate the DRX behavior of the steel during hot deformation. These results indicated that the rheological stress of Fe–28Mn–10Al–1.5C–0.6V steel at low shows higher temperature sensitivity and that high T and low are conducive to the occurrence of DRX. The average relative error of the ANN constitutive model is 2.40%, which has high prediction accuracy. The dynamic recrystallization conditions determined by the above models are reliable and conform to the experimental rules. By verifying the microstructure of the steel after thermal compression, the prediction error of the finite element model to the DRX volume fraction is mostly within 10%. Thus, the model has a good predictive ability and provides an effective tool for predicting plastic deformation and microstructure in industrial production.

Dynamic Recrystallization Behavior of an Alumina-forming Austenitic Alloy Fe-20Cr-30Ni-0.6Nb-2Al-Mo

Dynamic Recrystallization Behavior of Fe–20Cr–30Ni–0.6Nb–2Al–Mo Alloy

Characteristic and Mechanism of Dynamic Recrystallization in a Newly Developed Fe-Cr-Ni-Al-Nb Superalloy During Hot Deformation

Research on dynamic recrystallization behavior of Ni Fe Cr based alloy

Mechanism of dynamic recrystallization of a FeCrAl alloy during hot compression

Hot Deformation and Dynamic Recrystallization of 7075 Al Alloy in the Extruded State

Investigation of dynamic recrystallization and modeling of microstructure evolution of an Al-Mg-Si aluminum alloy during high-temperature deformation

Microstructure evolution and dynamic recrystallization mechanism during thermal deformation of GH4698 superalloy

Dynamic Recrystallization Behaviour of Nb-Ti Microalloyed Steels

Dynamic recrystallization mechanisms of as-forged Al–Zn–Mg-(Cu) aluminum alloy during hot comp.ression deformation

Hot deformation behaviors of low-alloyed ultrahigh strength steel 30CrMnSiNi2A: Microstructure evolution and constitutive modeling

Hot deformation behavior and dynamic recrystallization of dual-phase (CrCoNi)94Al3Ta3 medium entropy alloy

Effect of deformation parameters and Al 2 Cu evolution on dynamic recrystallization of 2219-O Al alloy during hot compression

Modeling of Dynamic Recrystallization Evolution for Cr8 Alloy Steel and Its Application in FEM

On Microstructure Characterization of Fe–Cr–Ni–Mo–N Super-Austenitic Stainless Steel During Hot Deformation

Investigation of Isothermal Continuous Hot Deformation Behavior of the New As-Cast Alumina-Forming Austenitic Alloy

Modeling of Dynamic Recrystallization Volume Fraction Evolution for AlCu4SiMg Alloy and Its Application in FEM

Dynamic recrystallization and hot processing map of Ti-48Al-2Cr-2Nb alloy during the hot deformation

Research on hot deformation, dynamic recrystallization and numerical simulation of Fe–28Mn–10Al–1.5C–0.6V steel

The kinetics of dynamic recrystallization and construction of constitutive modeling of RAFM steel in the hot deformation process

Continuous Dynamic Recrystallization and Deformation Behavior of an AA1050 Aluminum Alloy during High-Temperature Compression