Abstract:Many studies have been carried out on the phosphating of steel and aluminum alloys used in automotive engineering, but characterization of the properties of the phosphate layers formed by the co-phosphating of these alloys in the presence of different base metals is still lacking. In this study, the crystal structure and properties of the phosphate conversion layers formed on the surface of the aluminum alloys important in vehicle manufacturing (cast and forged AlSi1MgMn, and AA6014 panel) and the CRS SAE 1008/1010 reference steel plate by co-deposition prior to painting were investigated. On a process line set up for the phosphating of typical iron and steel alloys, the phosphate coating was formed using nitrite and nitroguanidine accelerators under identical technological parameters. The microstructure of the formed phosphate layers was examined using scanning electron microscopy (SEM), its phase composition using X-ray diffraction (XRD), and its elemental composition using energy-dispersive X-ray analysis (EDX). The suggested main crystalline phase (Zn2.3(Ni0.1Mn0.6)(PO4)2·4H2O) in the surface phosphate layer of both aluminum alloys studied was similar to hopeite, whereas in the steel plate, a minor hopeite phase were identified in addition to the main crystalline phosphophyllite phase (~95%). It can be concluded that, during the combined phosphating treatments, the surfaces of different aluminum and steel alloys behaved similarly to the individual treatments and did not impede the coating reactions of the other metal. To obtain an adequate coating of aluminum and steel alloys, fluoride should always be present in the production line. Comparing the effects of accelerators, we found that the use of nitrite accelerator with the same amount of fluoride resulted in a higher coverage and better quality of the surface protective layer of the aluminum alloys. However, for the steel plate, there was no significant difference between the phosphate coatings prepared with the two different accelerators.

Preparation and Corrosion Mechanism Research of Anticorrosive Phosphate Film Containing Zn-Al

New Zinc-phosphating Process with RE Catalyzer at Low Temperature for Painting Pretreatment of Cold-rolling A3 Steel Sheet

Construction and Study on Corrosion Protective Property of Polydopamine-Based 3-Layer Organic Coatings on Aluminum Substrate

Technology and Mechanism for Zinc-System Phosphating of Aluminum

A Phosphating Technology for Aluminium Alloy

Corrosion-resistant Plasma Electrolytic Oxidation Coating Modified by Zinc Phosphate and Self-Healing Mechanism in the Salt-Spray Environment

Corrosion and Protection Characteristics of Phosphate Coatings on Aluminum Alloy 6061 Using Yttrium Oxide as Additive

Effect of Process Parameters on Properties of Cold-Sprayed Zn–Al Composite Coatings

Crystal Structure and Properties of Zinc Phosphate Layers on Aluminum and Steel Alloy Surfaces

Zinc coating on steel by atmosphere plasma spray and their anti-corrosion behavior

Study of ZnAl Hydroxides-Based Thin Films to Enhance the Filiform Corrosion Resistance of Acrylic-Coated AA5005

Preparation and Properties of Phosphate-Fluorocarbon Acrylate Anticorrosion Emulsion

Effect of Al Content on the Long-Term Corrosion Behavior of Arc-Sprayed ZnAl Alloy Coatings

A Study and Application of Zinc Phosphate Coating on Az91d Magnesium Alloy

Influence of synergistic effect of phosphate on corrosion resistance of self-assembled superhydrophobic composite film on 6061 aluminum alloy surfaces

Preparation and study of a molybdate passivation film on zinc alloy

Preparation, Wear Resistance, and Corrosion Performance of Arc-Sprayed Zn, Al, and Zn-Al Coatings on Carbon Steel Substrates

Influence of Al contents on the long-term corrosion behaviors of cold-sprayed Zn-xAl coatings

Monododecyl Phosphate Film on LY12 Aluminum Alloy: pH-Controlled Self-Assembly and Corrosion Resistance

The Role of Zinc Phosphate Pigment in the Anticorrosion Properties of Bisphenol A Diglycidyl Ether-Polyaminoamide Coating for Aluminum Alloy AA2024-T3

A zinc-doped coating prepared on the magnesium alloy by plasma electrolytic oxidation for corrosion protection