Abstract:Many studies have been carried out on the phosphating of steel and aluminum alloys used in automotive engineering, but characterization of the properties of the phosphate layers formed by the co-phosphating of these alloys in the presence of different base metals is still lacking. In this study, the crystal structure and properties of the phosphate conversion layers formed on the surface of the aluminum alloys important in vehicle manufacturing (cast and forged AlSi1MgMn, and AA6014 panel) and the CRS SAE 1008/1010 reference steel plate by co-deposition prior to painting were investigated. On a process line set up for the phosphating of typical iron and steel alloys, the phosphate coating was formed using nitrite and nitroguanidine accelerators under identical technological parameters. The microstructure of the formed phosphate layers was examined using scanning electron microscopy (SEM), its phase composition using X-ray diffraction (XRD), and its elemental composition using energy-dispersive X-ray analysis (EDX). The suggested main crystalline phase (Zn2.3(Ni0.1Mn0.6)(PO4)2·4H2O) in the surface phosphate layer of both aluminum alloys studied was similar to hopeite, whereas in the steel plate, a minor hopeite phase were identified in addition to the main crystalline phosphophyllite phase (~95%). It can be concluded that, during the combined phosphating treatments, the surfaces of different aluminum and steel alloys behaved similarly to the individual treatments and did not impede the coating reactions of the other metal. To obtain an adequate coating of aluminum and steel alloys, fluoride should always be present in the production line. Comparing the effects of accelerators, we found that the use of nitrite accelerator with the same amount of fluoride resulted in a higher coverage and better quality of the surface protective layer of the aluminum alloys. However, for the steel plate, there was no significant difference between the phosphate coatings prepared with the two different accelerators.

A Phosphating Technology for Aluminium Alloy

New Zinc-phosphating Process with RE Catalyzer at Low Temperature for Painting Pretreatment of Cold-rolling A3 Steel Sheet

Technology and Mechanism for Zinc-System Phosphating of Aluminum

Effect of Phosphating Technologies on Corrosion Resistance of Phosphate Coatings on 6063 Aluminum Alloy

A Study and Application of Zinc Phosphate Coating on Az91d Magnesium Alloy

Aluminum alloy surface phosphatizing fluid and phosphatizing method

Corrosion and Protection Characteristics of Phosphate Coatings on Aluminum Alloy 6061 Using Yttrium Oxide as Additive

Phosphating Suitability and Coating Corrosion Resistance of Alloy Galvanized Sheet

Anti-corrosion Performance of LY12 Al Alloy Reinforced by Anodic Oxidization and Silanization

Wear and corrosion resistant coatings prepared on LY12 aluminum alloy by plasma electrolytic oxidation

Crystal Structure and Properties of Zinc Phosphate Layers on Aluminum and Steel Alloy Surfaces

Environment-friendly aluminum alloy chromium-free phosphating solution and preparation method thereof

Zinc Phosphating Accelerated by Rare Earth Nitrate on Aluminum Alloy

A Method for Electroless Nickel Plating on Aluminum Alloy Surface

Electroless Ni–P deposition plus zinc phosphate coating on AZ91D magnesium alloy

Influence of a Phosphate–Nitrate Composition on the Corrosion of Mechanically Activated Aluminum Alloy

Monododecyl Phosphate Film on LY12 Aluminum Alloy: pH-Controlled Self-Assembly and Corrosion Resistance

Corrosion Behavior of ZnO-reinforced Coating on Aluminum Alloy Prepared by Plasma Electrolytic Oxidation

Nickel-free sealing technology for anodic oxidation film of aluminum alloy at room temperature

Excellent Corrosion Resistance of P and Fe Modified Micro-Arc Oxidation Coating on Al Alloy

Effect of Alkaline Etching on Formation Behavior and Corrosion Resistance of a Cr-Zr-Ti TCP Conversion Coating on AA2024 Aluminum Alloy