Abstract:Ionic polymer–metal composites (IPMC), one of the most popular materials in the field of artificial muscle research, have attracted much attention because of their high flexibility, low drive voltage (<10 V), high force density, large deformation, and so forth. However, the results show that the serious electrode fatigue crack and water loss of traditional IPMC greatly decrease its fatigue life and limit the practical application. In this study, we developed a novel liquid metal composite electrode. A layer of eutectic gallium–indium alloy (EGaIn) liquid metal was applied to the surface of the platinum electrode of the IPMC using a mask. Because of the good self-healing performance of the liquid metal, it is expected to solve the above problems of resistance increase and water loss caused by cracks. It turns out that the prepared EGaIn/Pt-IPMC exhibits a driving force up to 120 mN and maximum fatigue life of about 25,000 s at a driving voltage of 3 V. Compared with the best work reported, the fatigue strength of EGaIn/Pt-IPMC was increased by about 210%, and the maximum driving force of EGaIn/Pt-IPMC prepared by a single-layer basement membrane was between the IPMC prepared by 4–6 layer basement membrane. The electromechanical properties were significantly improved, and it is expected to realize a series of bionic applications.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.2c01453.Additional performance characterization data for EGaIn/Pt-IPMC, such as the effect of drive voltage frequency and amplitude on displacement, and the ability of EGaIn to repair cracked electrode IPMC (including drive force enhancement and fatigue displacement enhancement) (PDF)Imitating fish tail wobble (MP4)Imitating dragonfly wings (MP4)Bionic artificial hand (MP4)High-amplitude high-frequency swing (MP4)This article has not yet been cited by other publications.

Fabrication and characteristics of the 3-dimensional IPMC with gradient structure

A three-electrode structured ionic polymer carbon-composite actuator with improved electromechanical performance

Low-Voltage Driven Ionic Polymer-Metal Composite Actuators: Structures, Materials, and Applications

Preparation and characterisation of IPMC brakes modified with composite electrodes performance

Property of ionic polymer metal composite with different thicknesses based on solution casting technique

A Compact Review of IPMC as Soft Actuator and Sensor: Current Trends, Challenges, and Potential Solutions From Our Recent Work

Preparation and performance research of porous and venus flytrap-shaped IPMC

Printing ionic polymer metal composite actuators by fused deposition modeling technology

Fabrication and Characterization of a Novel Smart-Polymer Actuator with Nanodispersed CNT/Pd Composite Interfacial Electrodes

Improve the Performance of Mechanoelectrical Transduction of Ionic Polymer-Metal Composites Based on Ordered Nafion Nanofibres by Electrospinning

Development of Ionic Polymer-Metal Composite

Deformation Performance of Pt-IPMC Based on Experiment and Simulation Research

Beta-2-microglobulin level predicts outcome following autologous hematopoietic stem cell transplantation in patients with multiple myeloma.

An Antifatigue Liquid Metal Composite Electrode Ionic Polymer-Metal Composite Artificial Muscle with Excellent Electromechanical Properties

3D Printing of Layered Structures of Metal-Ionic Polymers: Recent Progress, Challenges and Opportunities

A 3D analytical ion transport model for ionic polymer metal composite actuators in large bending deformations

Antibiotic use and microbial resistance in intensive care units: impact of computer-assisted decision support.

Application-oriented simplification of actuation mechanism and physical model for ionic polymer-metal composites

Review on Improvement, Modeling, and Application of Ionic Polymer Metal Composite Artificial Muscle

Bioinspired Anisotropic Microstructures toward Multimodal Deformations of Low‐Voltage‐Driven Ionic Actuators

Improved manufacturing technology for producing porous Nafion for high-performance ionic polymer–metal composite actuators