Abstract:Ionic polymer–metal composites (IPMC), one of the most popular materials in the field of artificial muscle research, have attracted much attention because of their high flexibility, low drive voltage (<10 V), high force density, large deformation, and so forth. However, the results show that the serious electrode fatigue crack and water loss of traditional IPMC greatly decrease its fatigue life and limit the practical application. In this study, we developed a novel liquid metal composite electrode. A layer of eutectic gallium–indium alloy (EGaIn) liquid metal was applied to the surface of the platinum electrode of the IPMC using a mask. Because of the good self-healing performance of the liquid metal, it is expected to solve the above problems of resistance increase and water loss caused by cracks. It turns out that the prepared EGaIn/Pt-IPMC exhibits a driving force up to 120 mN and maximum fatigue life of about 25,000 s at a driving voltage of 3 V. Compared with the best work reported, the fatigue strength of EGaIn/Pt-IPMC was increased by about 210%, and the maximum driving force of EGaIn/Pt-IPMC prepared by a single-layer basement membrane was between the IPMC prepared by 4–6 layer basement membrane. The electromechanical properties were significantly improved, and it is expected to realize a series of bionic applications.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.2c01453.Additional performance characterization data for EGaIn/Pt-IPMC, such as the effect of drive voltage frequency and amplitude on displacement, and the ability of EGaIn to repair cracked electrode IPMC (including drive force enhancement and fatigue displacement enhancement) (PDF)Imitating fish tail wobble (MP4)Imitating dragonfly wings (MP4)Bionic artificial hand (MP4)High-amplitude high-frequency swing (MP4)This article has not yet been cited by other publications.

An Antifatigue Liquid Metal Composite Electrode Ionic Polymer-Metal Composite Artificial Muscle with Excellent Electromechanical Properties

High‐Performance Ionic‐Polymer–Metal Composite: Toward Large‐Deformation Fast‐Response Artificial Muscles

High Specific Surface Area Pd/Pt Electrode-Based Ionic Polymer–Metal Composite for High-Performance Biomimetic Actuation

Electromechanical Performances of IPMC Actuator Enhanced by High-Quality Pd/Pt Electrodes*

Fabrication and Performance of Ionic Polymer-Metal Composites for Biomimetic Applications

Review on Improvement, Modeling, and Application of Ionic Polymer Metal Composite Artificial Muscle

High-performance Biocompatible Nano-Biocomposite Artificial Muscles Based on a Renewable Ionic Electrolyte Made of Cellulose Dissolved in Ionic Liquid

Highly Flexible, Large-Deformation Ionic Polymer Metal Composites for Artificial Muscles: Fabrication, Properties, Applications, and Prospects

Soft Artificial Muscle of Poly(vinyl Chloride) Gel with an Imperceptible Liquid Metal Electrode

Low-Voltage Driven Ionic Polymer-Metal Composite Actuators: Structures, Materials, and Applications

Ionic Polymer-Metal Composites: From Material Engineering to Flexible Applications

Design and Preparation of Biomorphic IPMC and Its Performance Research

Preparation and Properties of Ionic Exchange Polymer Metal Composites for Actuator

Fabrication and Actuation of Cu-Ionic Polymer Metal Composite

Deformation Performance of Pt-IPMC Based on Experiment and Simulation Research

High water content electrically driven artificial muscles with large and stable deformation for soft robots

Investigation on the Preparation of Ionic Polymer-Metal Composite(IPMC)

Property of ionic polymer metal composite with different thicknesses based on solution casting technique

Recent Advances of Ionic Polymer-Metal Composites

A Compact Review of IPMC as Soft Actuator and Sensor: Current Trends, Challenges, and Potential Solutions From Our Recent Work

Analysis of the Impact of Electrochemical Properties of Copper-Doped Electrode Membranes on the Output Force of Biomimetic Artificial Muscles