Abstract:The 2195 Al-Cu-Li alloy is widely utilized for the fabrication of key aerospace vehicle components; hence, an in-depth understanding of its hot deformation behavior is essential for consistently achieving high-performance products. In this study, isothermal compression tests were performed on 2195 Al-Cu-Li alloy ingots in the temperature and strain rate ranges of 250–500 °C and 10 −3 -1 s −1 , respectively. A processing map was established to predict the workability under different conditions. The corresponding microstructures were examined to reveal their hot deformation mechanism. Results demonstrated that the processing map was divided into four distinct domains. The unstable zone was located in the 250–375 °C/10 −1.5 -1 s −1 and 250–275 °C/10 −2.5 –10 −1.5 s −1 , temperature/strain rate regimes, in which deformation bands and flow localization were observed. The deformation bands blocked dislocations and compromised the dynamic recrystallization (DRX) behavior, hence damaging the microstructure. Further, large coarse T 1 phases precipitated in the 325–410 °C/10 −2.5 –10 −3 s −1 regime, which led to the formation of heterogeneities in the microstructure, corresponding to a minimum workability in the processing map. The optimal hot-working domain for the 2195 alloy was determined to be 460–500 °C/10 −3 –10 −2 s −1 , and the dominating hot deformation mechanisms were DRX and dynamic recovery (DRV). Specifically, continuous and discontinuous DRX behaviors dominated in the 300–400 °C/10 −3 s −1 and 450–500 °C/10 −3 s −1 regimes, respectively. DRX gradually weakened as the strain rate increased at 500 °C. Further, the weakening of DRX was only minimally affected by temperature at 400–500 °C during high-speed deformation (1 s −1 ). The results reported herein can provide valuable insights into the hot working of Al-Cu–Li alloys.

Hot deformation behavior of AA2 1 9 5 alloy during isothermal compression at elevated temperature

Tensile Deformation Behaviors of Aluminum Alloy 2219 at High Temperatures from 415°C to 515°C

Hot Deformation Behavior of 2026 Aluminum Alloy During Compression at Elevated Temperature

Hot deformation behavior and microstructure characteristic of 2055 Al-Li alloy during uniaxial compression

Study on Hot Deformation Behavior of TA15 Alloy

Hot Deformation Behavior and Dynamic Recrystallization of 6061 Aluminum Alloy

Effect of heat treatment on hot deformation behavior and microstructure evolution of 2195 Al-Li alloy

Dynamic recrystallisation and dynamic precipitation in AA6061 aluminium alloy during hot deformation

Unified Constitutive Model of Aluminum Alloy 2219 at Elevated Temperature

Hot deformation behavior of high Zn-containing 7A65 Al alloy

Investigation on hot deformation behavior of 2050 Al-Cu-Li alloy

Hot deformation behavior and microstructural evolution of particulate reinforced AA6061/B4C composite during compression at elevated temperature

Characterization of Hot Deformation Behavior and Processing Maps of Homogenized Al-Mg-Si-Sc-Zr Alloys

Hot deformation behavior and microstructural evolution of the Al-Cu-Li alloy: A study with processing map

Hot Deformation Behavior and Microstructure Evolution of Al-7.92 Zn-1.64 Mg-2.00 Cu Alloy

Constitutive Analysis and Microstructure Characteristics of As-Homogenized 2198 Al–Li Alloy under Different Hot Compression Deformation Conditions

Hot Deformation Behavior of Homogenized Al-7.8Zn-1.65Mg-2.0Cu (wt.%) Alloy

Constitutive behavior and novel characterization of hot deformation of Al-Zn-Mg-Cu aluminum alloy for lightweight traffic

Analysis of hot Formability of Al-4.6Mg-0.6Mn Alloy (AA5083)

Hot Workability and Microstructure Evolution of Homogenized 2050 Al-Cu-Li Alloy during Hot Deformation

Hot deformation behavior of AZ40 magnesium alloy at elevated temperatures