Abstract:The microstructural evolution of a single-phase Cu–12Mn–3Ni alloy during rolling and annealing has been investigated using electron backscatter diffraction and X-ray diffraction techniques. We have established the effects of microstructural characteristics on material strength and the temperature coefficient of resistance (TCR). The yield strength increased to 682 MPa after cold rolling with a strain of 0.87 due to an increase in the density of dislocation and low-angle grain boundary. A significant annealing softening is observed for the cold-rolled Cu–Mn–Ni alloy at temperatures above 400 °C, caused by recrystallization. The difference in yield strength for fully recrystallized alloys is mainly attributed to a difference in grain size, consistent with the Hall–Petch relationship. The addition of Ni and Mn enhanced the degree of difficulty in dislocation passing through the grain boundary, resulting in a higher Hall-Petch constant (274 MPa μm 1/2 ) for Cu–12Mn–3Ni alloys when compared with pure copper. The TCR is related to grain size, dislocation and Cu–12Mn–3Ni alloy texture. Grain coarsening and reduced dislocation density can effectively enhance the resistance temperature stability. In addition, the strong copper texture formed during cold rolling results in a difference in TCR associated with the rolling direction (RD) and transverse direction (TD) of the cold-rolled sheet. The Cu–Mn–Ni alloy crystal exhibits a lower resistance sensitivity to temperature when the [110] Cu direction is parallel to the current direction compared with the [111] Cu direction parallel to the current direction. The absolute value of the TCR in the TD of the cold-rolled sheet is 10.2 × 10 −6 °C −1 , lower than that in the RD (19.3 × 10 −6 °C −1 ).

Influences of Trace Residual Elements Cr,Ni and Cu on Microstructures and Tensile Properties of SPHC Cold-Rolled Strip

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Effects of Cold Rolling Reduction Rate on the Microstructure and Properties of Cu-1.16Ni-0.36Cr Alloy after Thermo-Mechanical Treatment

Microstructure and Properties of Cold Drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe Alloys

Synergistic effects of the TiC nanoparticles and cold rolling on the microstructure and mechanical properties of Al–Cu strips fabricated by twin-roll casting

The Effects of Refractory Elements on Mechanical Properties in CoCrNiFe Concentrated Solid Solution Alloys Across Different Temperatures

Effect of C and Mn element partitioning behavior on microstructure and properties of cold-rolled medium manganese TRIP steel

Influence of Heat Treatment on the Texture, Microstructure and Tensile Deformation Behaviours of Cold Rolled FeCoNiCr Sheets

Influence of Different Rolling Processes on Microstructure and Strength of the Al–Cu–Li Alloy AA2195

Influence Mechanisms of Cold Rolling Reduction Rate on Microstructure, Texture and Magnetic Properties of Non-Oriented Silicon Steel

Microstructure and Properties of Cold Rolled Cu70Cr30 Composite

Effect of Rolling Reduction on Microstructures and Mechanical Properties of Sc-Containing Al-3.2Cu-1.5Li Alloy

Microstructures, Mechanical Properties and Deformation of Near-Rapidly Solidified Low-Density Fe-20Mn-9Al-1.2C-xCr Steels

Dependence of resistivity on temperature and the mechanism of strengthening in a single-phase Cu–12Mn–3Ni alloy

The tensile properties and microstructure evolution of cold-rolled Fe–Mn–C TWIP steels with different carbon contents

The Influence of the Hot-Rolling Temperature on the Microstructure and Mechanical Properties of Ti-Nb Microalloyed 21%Cr Ferritic Stainless Steel

Effect of Cold Rolling Process on Microstructure, Texture and Properties of Strip Cast Fe-2.6%Si Steel

Microstructures and textures in cold-rolled aluminium strip

Effect of Cold Rolling and Cryogenic Treatment on the Microstructure and Mechanical Properties of Fe–32Ni Alloy

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel

Effects of Cold Rolling Pre-Strain on Abnormal Grain Growth Behavior in Longitudinal Welds of 2196 Al-Cu-Li Profiles