Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

New Process of Drop Feed Gas Carburizing with High Rate

Use of Nitrogen Gas in High-Speed Milling of Ti-6Al-4V

Plasma Nitrocarburising Process and Microstructure and Properties for High Thickness Compound Layer of 42crmo Steel

A New Process of Solveing Corrosion Problem of Refined Liquefied Gas

Surface strengthening mechanism of the active grinding carburization

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Microstructure Evolution and Mechanical Properties of High-Temperature Carburized 18Cr2Ni4WA Steel

Diffusion behavior of carbon and its hardening effect on plasma carburized M50NiL steel: Influences of treatment temperature and duration

Effect of Post-Plasma Nitrocarburized Treatment on Mechanical Properties of Carburized and Quenched 18Cr2Ni4WA Steel

Effect of surface nanocrystallization on low-temperature gas carburization for AISI 316L austenitic stainless steel

Experimental Study on Vacuum Carburizing Process for Low-Carbon Alloy Steel

Study of surface properties of Ti-6Al-4V with double-glow plasma non-hydrogen carburizing

Improvement of Chemical Liquid Vaporized Infiltration Process for Fast Densification of Carbon/Carbon Composites

The thermal process for hardening the nitrocarburized layers of a low-carbon steel

Surface modification of CoCrFeNi high entropy alloy by low-temperature gaseous carburization

The Effect of Surface Self-Nanocrystallization on Low-Temperature Gas Carburization for AISI 316L Steel

Carburization-induced microstructure evolution and hardening mechanism of 18CrNiMo7-6 steel

Factors Affecting the Hardness Characteristics of Microstructures in Gas Carburized Chromium Alloy Steels

Mechanical properties of low-temperature gaseous carburizated layer in 316L stainless steel based on nano-indentation and four-point bending tests

Further enhancement of surface mechanical properties of carburized 9310 steel by electropulsing-assisted ultrasonic surface rolling process