Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Effects of Temperature on the Viscosity of Partially Hydrolyzed Polyacrylamide

Study on the Viscosity of Polymer Polyol

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Study of the effects of water content and temperature on polyacrylamide/polyvinyl alcohol interpenetrating network hydrogel performance by a molecular dynamics method

Rheological Properties of Template Polymerization Polyacrylamide Aqueous Solutions

A Study on the Thermal Degradation of an Acrylamide and 2-Acrylamido-2-Methylpropanesulfonic Acid Copolymer at High Temperatures

Effect of degree of hydrolysis of polyacrylamide on the micromorphology of its solution

Decrease in Viscosity of Partially Hydrolyzed Polyacrylamide Solution Caused by the Interaction Between Sulfide Ion and Amide Group

Behaviors of Water Molecules in Polyvinyl Alcohol Gel Amid Stretch and Temperature Changes: A Molecular Dynamics Study

Effect of Thermal History on Rheological Properties of Partially Hydrolyzed Polyacrylamide/Anionic Surfactant SDS Complex Systems

Influence of Hydrogen-bond on the Rheological Behavior of Poly(vinyl Alcohol)

Interaction between HPAM and urea in aqueous solution and rheological properties

Prevention of network destruction of partially hydrolyzed polyacrylamide (HPAM): Effects of salt, temperature, and fumed silica nanoparticles

Study on Self-Assembly Properties of Thermosensitive Fluorinated Hydrophobically Associating Polyacrylamide

Solution behavior of fluorocarbon-modified polyacrylamide copolymers

Adsorption Behavior and Shear Degradation of Ultrahigh‐molecular‐weight Hydrolyzed Polyacrylamide in a Capillary Flow

Molecular Simulation Studies on the Interaction Between Different Polymers in Aqueous Solution

The effect of three types of cross-linked hydrogels and volume fraction of polyacrylamide on the swelling and thermal behavior using molecular dynamics simulation

Incorporation of Partially Hydrolyzed Polyacrylamide With Zwitterionic Units and Poly(Ethylene Glycol) Units Toward Enhanced Tolerances to High Salinity and High Temperature

Understanding the viscosity decline of poly(amic acid) solution from the correlation point of view

Rheology Control by Modulating Hydrophobic and Inclusive Associations of Side‐groups in Poly (acrylic Acid)