Abstract:To achieve the objective of enhancing both strength and toughness of marine 10Ni5CrMoV steel, the tempering process is optimized. By leveraging both dislocation strengthening and precipitation strengthening, the strength is boosted to 876 MPa. The reduction in the precipitates size effectively hinders the cracks, which is responsible for reducing the ductile‐brittle transition temperature to −116 °C. The microstructure and mechanical properties of marine 10Ni5CrMoV steel are systematically investigated at tempering temperatures ranging from 630 to 670 °C. With increasing tempering temperature, several key parameters exhibit notable changes: the volume fraction of reversed austenite decreases from 17.36% to 13.39%. The equivalent grain size increases from 0.91 to 1.09 μm. The equivalent diameter of precipitates increases from 59 to 79 nm. The dislocation density decreases from 0.82 × 10−15 to 0.51 × 10−15 m−2. As the tempering temperature increases, the pinning effect of precipitates on dislocations and martensite laths decreases. This leads to reductions in both dislocation strengthening and precipitation strengthening mechanisms. Consequently, the yield strength of the specimen decreases from 876 to 683 MPa. The increase in the ductile‐brittle transition temperature of the specimens from −116 to −95 °C can be attributed to several factors. First, the increase in precipitate size reduces the critical nucleation stress of cleavage cracks and promotes the nucleation of such cracks. Additionally, the decrease in dislocation density mobility leads to a reduction in the dimple nucleation rate, thereby diminishing the role of dimples in hindering crack propagation.

Industrial Production of 780 MPa Grade Tempering Steel Plates for Cold Forming and for Hot-Strip Rolling

Effect of Tempering Temperatures on Microstructure and Mechanical Properties of High-Strength Steel

Enhanced Yield Strength and Total Elongation of an Ultrahigh Strength Hot‐Stamped Steel via Tempering Treatment

Effects of Heat Treatment Process on Microstructure and Mechanical Properties for Extra-Thick High-Strength Steel Plate

Study on Direct Quenching and Tempering Process of 1000mpa Grade Low Alloy High Strength Steel

Strengthening of Ultrafine Lamellar-Structured Martensite Steel Via Tempering-Induced Nanoprecipitation

Development of high strength plates with low yield ratio by the combination of TMCP and inter-critical quenching and tempering

Study on Quenching and Tempering Process of 800 MPa High Strength Steel Plate

Influence of Tempering Temperature on Annealed Microstructure of Dual-phase Steel

Achieving 1.7 GPa Considerable Ductility High-Strength Low-Alloy Steel Using Hot-Rolling and Tempering Processes

Regulation Law of Tempering Cooling Rate on Toughness of Medium-Carbon Medium-Alloy Steel

Tempering influence on microstructural evolution and mechanical properties in a core of CSS-42L bearing steel

Study on Microstructure and Mechanical Properties of Marine 10Ni5CrMoV Steel during Tempering

Synergetic Effects of Ferrite Content and Tempering Temperature on Mechanical Properties of a 960 MPa Grade HSLA Steel

Quenching-Partitioning-Tempering Process and Its Engineering Feasibility of 900 MPa Grade Hot-Rolled Plate

An Investigation on the Microstructure and Mechanical Properties in an Ultrafine Lamellar Martensitic Steel Processed by Heavy Warm Rolling and Tempering

Tempering Effects on the Stability of Retained Austenite and Mechanical Properties in a Medium Manganese Steel

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel

Effect of tempering process on the mechanical properties and corrosion resistance of E690 marine steel

Study on Diversified Carbide Precipitation in High‐Strength Low‐Alloy Steel during Tempering

Evolution of Microstructures and Mechanical Properties with Tempering Temperature in a Novel Synergistic Precipitation Strengthening Ultra-High Strength Steel