Abstract:Sintering behaviour of ashes from combustion of coal and biomass blends was experimentally investigated with a focus on the effect of ash preparation method. Blends of a Chinese anthracite, Jincheng coal, and two biomass materials, a wheat straw and a pine sawdust, respectively, were subjected to three different ash preparation procedures, namely, a low temperature oxygen plasma ashing device operating at ca 150 degrees C, combustion in a Muffle furnace at 815 degrees C and in a drop tube furnace at 1500 degrees C. The resulting ash samples were then subjected to the sintering temperature measurement using a pressure-drop sintering device, morphological and mineralogical characterisation using scanning electron microscope (SEM) fitted with X-ray energy dispersive spectroscopy (EDS) and X-ray diffractometry analyser (XRD), respectively. For the same coal and biomass blends but different ash preparation methods, the sintering temperatures were always the lowest for the ash samples from the plasma ashing device and the highest from drop tube furnace. SEM imaging showed that the texture of ash samples from the plasma ashing device was irregular, loose and more fibrous, indicating little interactions among the different mineral and inorganic constituents in the individual fuels. The muffle furnace and drop tube furnace ashes were denser and more uniform in shape as the mineral matter and inorganics became fused together. In addition, the drop tube furnace ashes were mostly in spherical-shape, indicating ash melting had occurred during combustion. The XRD analysis revealed that different minerals were present in the ash samples due to different ash preparation temperatures, with high temperature minerals present in the drop tube furnace ash. Biomass addition in the blends lowered the sintering temperature of corresponding ash; the higher the proportion of biomass in the blend, the lower the ash sintering temperature regardless the ashing method. At the same biomass addition ratio, the ash sintering temperature of the blend with the wheat straw addition was lower than that with the pine sawdust addition, because the wheat straw had a higher K and Cl content but lower Ca than the pine sawdust. The EDS and XRD analyses confirmed that the ashes of coal/wheat straw blends contained more K-bearing minerals, while the ashes of the coal/pine sawdust contained more Ca and K-bearing minerals. Both Ca and K-bearing minerals reacted with other minerals in the ash to form low temperature eutectics, leading to the reduction of sintering temperatures of the coal and biomass blends. However, the melting points of the K-containing minerals are higher than the Ca-containing minerals, therefore, the sintering temperatures of ash with the wheat straw addition were lower than those with the pine sawdust addition. (C) 2016 Elsevier Ltd. All rights reserved.

Research on effect of premixing pulverized coal and lime on sintering flue gas emission

Experimental Study on Effect of Flux Addition on the Sintering Harmful Gas Emission

EXPERIMENT STUDY ON THE EFFECT OF IRON ORE SINTER BEHAVIOR WITH ADDING BIOMASS

NOxremoval Coupled with Energy Recovery in Sintering Plant

The Effect of Adjusting Sinter Raw Mix on Dioxins from Iron Ore Co-Sintering with Municipal Solid Waste Incineration Fly Ash

Experiments on the Effect of Chemical Components of Coal Ash on the Sintering Temperature

Effect Of Pulverized Coal Concentration On Emission Characteristics Of Nox

Effect of Ca-Fe oxides additives on NOx reduction in iron ore sintering

Effect of Ash Preparation Method on the Sintering Characteristics of Ashes from Combustion of Coal and Biomass Blends

Effect of Coating Structure of Granulated Quasi‐fuel Particles in Iron Ore Sintering

Effect of Sinter Mix Properties on the Flame Front Properties and Iron Ore Sintering Performance

Emissions of air pollutants from sintering flue gas in the Beijing-Tianjin-Hebei area and proposed reduction measures

Influence of Coke Combustion on NOx Emission During Iron Ore Sintering

Experimental Investigation on the Conversion of Fuel-N to NOx of Quasi-Particle in Flue Gas Recirculation Sintering Process

Influence of Sintering Parameters of Different Sintering Layers on Nox Emission in Iron Ore Sintering Process

Study on Formation of SO2 and NOx in Coal Combustion with Limestone Injection

Influence Factors on PM2.5 and PM10 Emissions in Iron Ore Sintering Process

Experimental Investigation on the Mixing Performance of Heating Gas into the Low Temperature Sintering Flue Gas Selective Catalyst Reaction Facilities

Effects of Temperature and Circulating Flue Gas Components on Combustion and NOx Emissions Characteristics of Four Types Quasi-particles in Iron Ore Sintering Process

Flame Front Propagation and Sinter Strength Properties of Permeable Sintering Bed Prepared Via Enhanced Granulation with Hydrated Lime

Experimental study on the effect of limestone on SO2 and NO emission characteristics during coal/coke combustion