Abstract:The formation of the microstructure in the rheo-diecastings were studied by the experiment of rheo-diecasting with semi-solid A380 Aluminum alloy slurry. The results show that the grain diameter and shape factor of primary α-Al grains decreased and increased along the rheo-diecasting direction, respectively, making the primary α-Al grains gradually distributing uniformly. The combination of injection pressure and narrow gate of the runner and ingate was the main reason for the evolution of the primary α-Al grains, moreover, the collision and friction among primary α-Al grains during the filling were helpful for the refinement and spheroidization of the primary α-Al grains. The residual liquid solidified into the secondary solidification microstructure accompanied by the evolution of the primary α-Al grains. The accumulation of the fragments of the primary α-Al grains, the secondary α2-Al nuclei or grains which formed in previous positions, the effective nucleation rate of the residual liquid, and the collision and fraction among the secondary α2-Al grains and between the secondary α2-Al grain and the primary α-Al grains made the secondary solidification microstructure of the residual liquid present multiplex and complicate characteristics. In this paper, the formation of the microstructure in the rheo-diecastings were studied by the experiment of rheo-diecasting. During the rheo-diecasting, the grain diameter and shape factor of primary α-Al grains decreased and increased, respectively along the rheo-diecasting direction, which made the primary α-Al grains gradually distribute uniformly. The drifting of the fragments of the primary α-Al grains and secondary α2-Al nucleus, and the effective nucleation rate of the residual liquid played an important effect on the morphology of the secondary solidification structure.

Microstructures and mechanical properties of A380 aluminum alloy produced by rheo-diecasting process

MICROSTRUCTURES AND PROPERTIES OF AZ91D MAGNESIUM ALLOY PRODUCED BY FORCED CONVECTION MIXING RHEO-DIECASTING PROCESS

Study on Formation of Microstructure in Rheo-Diecastings of Semi-Solid A380 Aluminum Alloy Slurry

Microstructure and Mechanical Properties of Rheo-Diecasting AZ91D Mg Alloy

Study on Microstructures and Mechanical Properties of Rheo-Die Casting Semi-Solid A356 Aluminum Alloy

Microstructure and Property of Rheo-Diecasting Magnesium-Alloy with Forced Convection Mixing Process

Investigation of rheo-diecasting mold filling of semi-solid A380 aluminum alloy slurry

Microstructural Characteristics of the Rheo-Diecasting AZ91D Magnesium Alloy

Rheo-diecasting Process for Semi-Solid Aluminum Alloys

Study on Microstructure-Processing Relationship of a Semisolid Rheocasting A357 Aluminum Alloy

Microstructure and Mechanical Properties of Rheo-Die Casting YL112 Aluminum Alloy

New technique for preparing A356 alloy semisolid slurry and its rheo-diecast microstructure and properties

Solidification behavior and enhanced properties of semi-solid Al–8Si–0.5Fe alloys fabricated by rheo-diecasting

Study on Mechanical Properties and Heat Treatment Process of Die-Cast A380 Alloy

R-HPDC Process with Forced Convection Mixing Device for Automotive Part of A380 Aluminum Alloy

Microstructure and mechanical properties of rheo-diecasted A390 alloy

Towards high performance Al–Si–Fe alloy castings via rheo-diecasting: Effect of injection velocity and heat treatment on microstructure evolution and property

Mechanical Properties of Semi-solid Rheo-die Casting A356 Aluminum Parts

Microstructure and Mechanical Properties of Rheo-Diecast Hypereutectic Al–Si Alloy with 2%fe Assisted with Ultrasonic Vibration Process

Microstructure and Properties of Semi-Solid Rheo-Diecasting ZL201 Aluminum Alloy

Microstructure and Properties of Rheo-Diecast Al-20Si-2Cu-1Ni-0.4Mg Alloy with Direct Ultrasonic Vibration Process