Abstract:This work improves the tribological behavior via innovative surface designs for slipper pairs in seawater axial piston pumps. 316L stainless steel and carbon fiber/polyether ether ketone (CF/PEEK) were selected as friction pair matching materials due to their good corrosion resistance, self-lubrication, and wear resistance. One type of smooth surface and five different types of pit nonsmooth surfaces were created on CF/PEEK specimens. Rotational sliding tests were performed on a friction and wear tester at a load of 200 N at five different sliding speeds (0.79, 1.18, 1.57, 1.96, and 2.36 m/s) under seawater lubrication. The experimental results indicate that the friction process of the smooth surface friction pair is mainly based on abrasive wear and adhesive wear. The friction coefficient range is 0.05–0.08, the specimen contact temperature is 38–75 °C, and the wear rates of 316L and CF/PEEK are 2.3 × 10−5 to 1.2 × 10−4 mm3/(MPa·m) and 5.6 × 10−4 to 7.6 × 10−3 mm3/(MPa·m), respectively. Pits on the specimen surface produce a hydrodynamic effect and store wear debris. The friction process of the nonsmooth surface friction pair is mainly controlled by a ploughing mechanism with only a slight amount of adhesive wear. The friction coefficient range is decreased to 0.03–0.07, the specimen contact temperature is decreased to 28–54 °C, and the wear rates of 316L and CF/PEEK are decreased to 1.2 × 10−5 to 9.1 × 10−5 mm3/(MPa·m) and 2.6 × 10−3 to 7.1 × 10−3 mm3/(MPa·m), respectively. The geometrical arrangement of the elliptical and tri-prism pits increases the convergence gap range and produces a higher bearing capacity. As the sliding speed increases, the friction coefficient first decreases and subsequently slightly increases, the specimen contact temperature increases, and the wear rate decreases.

Tribology Design of Sealing Materials Using Plastic Index

Tribological Properties of Seals in Integrated Transmission of Vehicle

Introduction to the Special Issue of Image-Guided Surgical Planning and Therapy

Study on Friction and Wear Performance of Sliding Metal Seal Materials Under Reciprocating Motion

Analysis of Friction and Wear Properties of Friction Ring Materials for Friction Rings under Mixed Lubrication

Tribological Analysis of Engineering Plastics/Steel Friction Pairs

Tribological Properties of Friction Pair between 316L Stainless Steel and CF/PEEK with Nonsmooth Surface under Seawater Lubrication

Analysis and Experimental Study on Friction and Wear Characteristics of Super High-Speed Mechanical Seal

Effect and performance analysis of different surface treatments on polymer-metal friction pairs

On Frictional Performance of Sintering Materials Used by Mechanical Seals in Water

Tribological Properties and Wear Mechanism of C/C Composite Applied in Finger Seal

Abrasive wear behavior of PTFE for seal applications under abrasive-atmosphere sliding condition

Dry Friction and Wear Properties of Several Hard Coating Combinations

Experimental Study on Texture Coupling Mechanism and Antifriction Performance of Piston Rod Seal Pair

Experimental investigation on frictional behavior and sealing performance of different composites for seal application

Influence of Variable-Depth Groove Texture on the Friction and Wear Performance of GCr15–SiC Friction Pairs Under Water Lubrication

Influence of diamond-like carbon coatings and micro-texturing on friction and wear of seal interfaces: Experiment and simulation study

Differences in Tribological Behaviors upon Switching Fixed and Moving Materials of Tribo-pairs including Metal and Polymer

Friction Behavior of a Textured Surface against Several Materials under Dry and Lubricated Conditions

Effect of Particle Size on Tribological Properties of Rubber/Steel Seal Pairs Under Contaminated Water Lubrication Conditions

Friction and wear behaviors of polycrystalline diamond self-mated pairs in air and water lubrication conditions