Abstract:Recently a contact solid carburization method to fabricate carbide coatings on refractory metals was proposed. The principle is to hot-press the refractory metal with a "carbon sponge" (e.g. cast iron or high-carbon steel) which contains interstitial carbon atoms. When they contact in atomic scale at high temperatures, the carbon atoms diffuse into the refractory metal matrix and then dense carbide coatings on the substrates can be obtained since most refractory metals are carbide forming elements. In this article, we apply this method to prepare carbide coating on molybdenum (Mo). Cast iron is used as the "carbon sponge" and hot-pressed with textured Mo at constant temperature and pressure (18 MPa). We set the temperature at 1100 degrees C and 900 degrees C separately, we found that coatings containing Fe-Mo-C layer and Mo-C layer are generated at 1100 degrees C while coatings containing only Mo-C layer are formed at 900 degrees C. We then hot-pressed the samples at 900 degrees C for 2-10 h and systematically investigated the microstructure and some basic properties of the coatings obtained at 900 degrees C. The coating grows inward, it is pure ceramic and completely dense. The coating is composed of columnar Mo2C grains whose grain orientations are randomly distributed. The metal and carbide phases are metallurgically bonded with incoherent interfaces. The coating thickness reaches 1.8 mu m when annealed for 10 h. As expected, the surface hardness is remarkably improved and the coating adhesion is strong. This technique is also expected to be used to improve the wear resistance, oxidation resistance for molybdenum and Mo based alloys and may also provide a new strategy to prepare Mo2C superconductors and catalysts.

Preparation And Analysis Of Molybdenum Coating On The Surface Of Silicon Carbide

Formation and Oxidation Behavior of Mo-Si-B Composite Coatings with B-rich Interlayer Prepared by Slurry Sintering Method

Fabrication of Mo2C Coating on Molybdenum by Contact Solid Carburization

Preparation of Molybdenum Coating on Surface of SiC Particles by Sol-Gel Method

Effect of interfacial modification on the thermo-physical property of SiCp/Cu composite

Microstructure and thermal properties of SiCp/Cu composites with Mo coating on SiC particles

Structure and properties of molybdenum-disulfide/amorphous carbon composited coatings deposited by co-sputtering method

Investigation of the Al-Mo-B(CN) Coatings Deposited Using Magnetron Sputtering of Al-Mo-B4C Target Produced by Detonation Spray Coating

Effect of Interfacial M Odifying on T Hermo-Physical Properties of SiCp/Cu Composites

Preparation and characterization of molybdenum disilicide coating on molybdenum substrate by air plasma spraying

Fabrication of silicon carbide coating on mullite fiber-reinforced mullite matrix composite via dip-coating

Micromorphology evolution, growth mechanism, and oxidation behaviour of the silicon-rich MoSi 2 coating at 1200 °C in air

Fabrication of CrSi2/MoSi2/SiC–Mo2C Gradient Composite Coating on Mo Substrate and the Stabilizing Effect of Cr on the Coating's Anti-Oxidation Properties

Wetting and Interfacial Behavior of Molten Al on Mo-Ni(Co)-Si Coated SiC Ceramic

A study on the cycling oxidation behavior of mullite-coated silicon carbide

Effects of Mullite Coating on the Anti-Oxidation of Silicon Carbide at High Temperature

Microstructure and High-Temperature Oxidation Resistance of Molybdenum Disilicide Coating

In-situ synthesis of MoSi 2 coating on molybdenum substrate by electro-deoxidation of a SiO 2 layer in molten salt

Study on the Structure and Formation Mechanism of Molybdenum Carbides

Unveiling the formation of Mo2C coating on diamond particles along with anisotropic etching by Mo powder

Effect of Reaction Temperature on the Molten Salt Electrodeposition of Silicide Coating on Molybdenum Substrate and its Oxidation Behavior