Abstract:Titanium alloys are known for being difficult to machine. Within the groups of Ti alloys, the machinability is reduced when going from the α-alloys, to α + β, and finally to near-β or β-alloys. Uncoated cemented carbide is traditionally used for machining these alloys and finding a suitable coating to improve the performance is a challenge due to the high strength of Ti alloys and the high chemical reactivity of Ti with tool and coating materials at the temperatures achieved during cutting. The PVD applied Ti x Al 1-x N (x = 0.4–0.7) is generally recommended for machining Ti alloys and a top layer of NbN has shown promising performance in milling applications. This study systematically explores the wear mechanisms of either uncoated WC-12%Co or its Ti 0.45 Al 0.55 N-NbN coated version in the milling of Ti alloys ranging from near-α (Ti-6Al-2Sn-4Zr-2Mo), α + β (Ti-6Al-2Sn-4Zr-6Mo), and near-β (Ti-5Al-5Mo-5 V-3Cr) alloys. The wear evolution is explored by studying as-worn tools and their cross-section using SEM-XEDS and EBSD after having reached 10%, 30%, 50%, and 100% of the full tool life at a flank wear criterion VB = 200 μm. The coating is removed within seconds of engagement and fails by cracking within the bulk and PVD droplet defects can initiate such cracks. Diffusional dissolution of the coating may be active on a minor scale, but the rapid mechanical failure shows the need for a more robust coating formulation. Exposed cemented carbide is worn at varying intensities when machining the Ti alloys. The highest wear rate is achieved in milling α + β Ti-6246, followed by a moderate wear rate in near-β Ti-5553, and with a slower wear rate in milling near-α Ti-6242 which is explained varying intensities in oxidation wear, diffusional dissolution, and mechanical cracking. Diffusional loss of C gives rounder WC grains and remaining W at the interface is removed by the chip flow. Diffusional loss of Co gives reduced grain bonding and loss of the dampening effect that leads to fractures in WC grains. Specifically in milling α + β Ti-6246 and in minor scale in near-α Ti-6242, there is formation of CoWO 4 ceramic present several μm into the tool and its formation is facilitated by the oxidation of binder with resolved W. Fractures within the CoWO 4 explains the high wear rate. Cracks also propagate in binder regions initiated from weakened interface regions due to diffusional loss of C and Co.

Wear Mechanisms of Coated Tool in High Speed Milling of AISI 4340 Alloy Constructional Steel

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel

Investigation on the Performance of Coated Carbide Tool during Dry Turning of AISI 4340 Alloy Steel

Analysis of tool wear and cutting characteristics in milling of powder metallurgy nickel-based superalloy by various coatings

Wear Mechanism of Multilayer Coated Carbide Cutting Tool in the Milling Process of AISI 4340 under Cryogenic Environment

Evaluation of wear mechanisms of PVD and CVD coatings deposited on cemented carbide substrates applied to hard turning

Performance and wear mechanisms of coated PCBN tools in high-speed turning superalloy GH4202

Study on the Wear Mechanism and Tool Life of Coated Gun Drill

Cutting Performance and Wear/Damage Characteristics of PCBN Tool in Hard Milling

ASSESSMENT OF WEAR AND DESTRUCTION OF SOLID CARBIDE CUTTERS DURING MILLING OF HARDENED STEEL 4X5MF1C WITH A HARDNESS OF 52 HRC

Enhancing Tool Performance in High-Speed End Milling of Ti-6Al-4V Alloy: The Role of AlCrN PVD Coatings and Resistance to Chipping Wear

Wear of End Mills with Carbon Coatings When Aluminum Alloy A97075 High-Speed Processing

Enhancing Wear Resistance and Cutting Performance of a Long-Life Micro-Groove Tool in Turning AISI 201

The effect of chip formation on the cutting force and tool wear in high-speed milling Inconel 718

On the wear mechanisms of uncoated and coated carbide tools in milling titanium alloys

Wear behavior of different coated tools in MQL-assisted high-speed milling of magnesium-based rare-earth alloys

Effect of ball nose flank wear on surface integrity in high-speed hard milling of AISI 4340 steel using MQL

Characterization of Tool Wear Mechanisms and Failure Modes of TiAlN-NbN Coated Carbide Inserts in Face Milling of Inconel 718

Wear characteristics and performance in side milling of Ti 2 AlNb intermetallic alloys with coated and uncoated end mills

Analysis of tool wear of TiAlN coated tool, machined surface morphology and chip during titanium alloy milling