Abstract:The changes in loading rate and test temperature influence deformation (yield and flow) and fracture behavior of steel. The most significant effect of increasing loading rate is to shift the quasi-static fracture toughness transition curve toward higher temperatures, that is, to raise the temperatures at which cleavage may occur. This is very critical for structural steel components. The high strain rate sensitivity of these steels makes the safety design on the basis of quasi-static behavior rather poor. Therefore, the reliability of structures possibly loaded at higher loading rates requires the knowledge of the corresponding material fracture behavior. However, the effects of loading rate on the cleavage fracture mechanism, fracture stress and toughness of various steels have not been understood completely. Specifically, the prediction of the cleavage fracture behavior in notched specimens and actual structures and components loaded at various loading rates remain to be learned. In engineering structures and components possibly loaded at various loading rates, notch defects may be difficult to avoid and some notch-like geometries are necessary for structure design. Therefore, the understanding of notch toughness at various loading rates is also very important. In this work, the effects of loading rate, notch geometry and loading mode on the cleavage fracture behavior of 16MnR steel were studied by experiments and FEM calculations. The results show that the cleavage fracture mechanism of this steel, the corresponding local cleavage fracture stress sigma(f) and macroscopic cleavage fracture stress sigma(F) do not change with the above three factors. The change of the notch toughness of the notched specimens with different notch geometries and loading modes with loading rates can be predicated by the criterion sigma(yymax) >= sigma(F), where sigma(yymax) is the maximum normal stress ahead of a notch and can be obtained by FEM calculations. The sigma(F) can be regarded as an engineering notch toughness parameter, and may be used for assessing the integrity of structures with notch defects. The sigma(F) values of steels can be measured by the Griffiths-Owen notched specimen at prescribed test temperature and loading rate.

PREDICTION OF DUCTILE FRACTURE IN TENSILE SPECIMENS WITH NOTCHES FOR A C-Mn STEEL BY USING GTN DAMAGE MODEL

Extended GTN Model for Predicting Ductile Fracture under a Broad Range of Stress States

Tensile Failure Modes in Nanograined Metals with Nanotwinned Regions

Material Parameters in the GTN Model for Ductile Fracture Simulation of G20Mn5QT Cast Steels

Modified Gtn Model for A Broad Range of Stress States and Application to Ductile Fracture

Ductile fracture prediction in aluminium alloy 5A06 sheet forming based on GTN damage model

A Statistical Model For Cleavage Fracture In Notched Specimens Of C-Mn Steel

Prediction of Ductile Fracture in Metalforming Processes Based on Meso-damage Model

Analysis of Metallic Ductile Fracture by extended Gurson models

Prediction of Fracture Behavior of 6061 Aluminum Alloy Based on GTN Model

A New Ductile Fracture Criterion for Various Deformation Conditions Based on Microvoid Model

DUCTILE DAMAGE ANALYSIS FOR FRACTURE IN SHEET METAL FORMING BASED ON GTN MESOSCOPIC DAMAGE MODEL

Anisotropic Gurson-Tvergaard-Needleman model considering the anisotropic void behaviors

EFFECTS OF LOADING RATE,NOTCH GEOMETRY AND LOADING MODE ON THE CLE AVA GE FRACTURE BEHAVIOR OF 16mnr STEEL

Cleavage Fracture Behavior of a C–Mn Vessel Steel at Various Loading Rates in Notched Specimens

Ductile Damage Analysis for Small Punch Specimens of Type 304 Stainless Steel Based on GTN Model

Ductile tearing analyses of cracked TP304 pipes using the multiaxial fracture strain energy model and the Gurson–Tvergaard–Needleman model

Ductile fracture prediction of additive manufactured Ti6Al4V alloy based on an extended GTN damage model

Extraction of Fracture Toughness Parameters by Ring-Notched Small Punch Specimen Using Cohesive Model

Ductile fracture prediction of HPDC aluminum alloy based on a shear-modified GTN damage model

An investigation on fracture toughness predictions from mini-sized uniaxial tensile specimens with global and local approaches