Abstract:The cyclic CO2 capture, transient phases change, and microstructure appearance of a new kind of Ca-based regenerable CO2 sorbent, CaO/Ca12Al14O33, obtained by the integration of CaO as solid reactant with a composite metal oxide of Ca12Al14O33 as a binder, were investigated by thermogravimetric analysis, XRD, and SEM at different preparation calcination temperatures. When the calcination temperature in the preparation stage is higher than 1000 degrees C, the cyclic CO2 capture of this new sorbent declines. The lowered CO2 capture may mainly be attributed to the formation of Ca3Al2O6, which decreases the ratio of CaO to binder in sorbent, and the severe sintering of sorbent occurs when calcined at such high temperatures in the preparation processes. These results suggest that the calcination temperature for this new sorbent should not be higher than 1000 degrees C in order to obtain its high reactivity. The performance of the new sorbent over 50 cycles was evaluated under mild and severe regeneration conditions, respectively. CaO/Ca12Al14O33 attained 41 wt % CO2 capture after 50 carbonation-calcination cycles under mild calcination conditions (850 degrees C, 100% N-2), and the results obtained here indicate that the new sorbent, CaO/Ca12Al14O33, has significantly improved CO2 capture and cyclic reaction stability over multiple carbonation-calcination cycles compared with limestone and dolomite under mild calcination conditions. When more severe calcination conditions (980 degrees C, 100% CO2) were used, the capture of CaO/Ca12Al14O33 decreased from 52 wt % in the first cycle to about 22 wt % in the 56th cycle; however, the capture of CaO/Ca12Al14O33 sorbent over 56 cycles is still higher than that of dolomite and limestone under the same severe calcination conditions.

CO2 Sorption Enhancement of Nano Calcium Carbonate Wrapped with the Mesoporous Skeleton

Preparation of cage-like nano-CaCO3 hollow spheres for enhanced CO2 sorption

Synthesis of a Porous Nano‐CaO/MgO‐Based CO2 Adsorbent

Properties of SiO_2 Coated Nano SiO_2/CaCO_3 Sorbents by Precipitation Method

Properties of a Nano CaO/Al2O3 CO2 Sorbent

Performance of Nano-Caco3 Coated with SiO2 on CO2 Adsorption at High Temperature

A new nano CaO-based CO2 adsorbent prepared using an adsorption phase technique

Adsorption Properties of Coating Modified Nano CaO-Based CO2 Adsorbents

Modified Kinetics Model of Nano CaO Reactions with CO2 in a CaO-Based Adsorbent

Properties of a Nano CaO/Al<sub>2</sub>O<sub>3</sub>CO<sub>2</sub>Sorbent

Behavior of CaTiO3/Nano-CaO As a CO2 Reactive Adsorbent

Synthesis and Performance of a Nano Synthetic Ca-based Sorbent for High Temperature CO_2 Capture

CO2 Capture Performance of CaO-Based Sorbents Prepared by a Sol–Gel Method

Morphological Changes of Pure Micro‐ and Nano‐Sized CaCO3 during a Calcium Looping Cycle for CO2 Capture

Cyclic Performance Of Waste-Derived Sio2 Stabilized, Cao-Based Sorbents For Fast Co2 Capture

Effect of Preparation Temperature on Cyclic CO2 Capture and Multiple Carbonation−Calcination Cycles for a New Ca-Based CO2 Sorbent

Investigation on a Novel CaO–Y2O3 Sorbent for Efficient CO2 Mitigation

Pore Structure Modified CaO-Based Sorbents with Different Sized Templates for CO2 Capture

Synthesis of CaO-based Sorbents Through Incorporation of Alumina/aluminate and Their CO2 Capture Performance

Sol–gel-Derived Synthetic CaO-Based CO2 Sorbents Incorporated with Different Inert Materials

Self-reactivated mesostructured Ca-Al-O composite for enhanced high-temperature CO2 capture and carbonation/calcination cycles performance.