Abstract:Sulfide‐polymer solid composite electrolyte (SCE) membranes are prepared for two sulfides (Li7PS6 and Li3PS4) incorporated into PVDF/HFP polymer electrolytes using a strong polar solvent (DMF). Li7PS6‐SCE exhibits better room temperature ionic conductivity than that of Li3PS4‐SCE. When increasing upper cut‐off voltages from 4.0 to 4.4 V, Li| Li7PS6‐SCE |NMC111 cells deliver higher discharge capacities but exhibit worse cycling stability. Solid composite electrolytes (SCEs) have attracted serious attention for solid‐state Li metal batteries. In particular, SCEs that incorporate inorganic sulfide into polymer electrolytes provide a feasible approach to address the air sensitivity and (electro)chemical instability of sulfides. Nevertheless, there is still little research on pairing sulfide‐SCEs with high‐voltage cathodes. In this work, reports on efforts to synthesize and compare SCEs that embedding sulfides (Li7PS6 and Li3PS4) into PVDF/HFP polymer using a strong polar solvent (DMF). Two sulfides show distinct behaviors when dispersed in the DMF solvent. The Li7PS6‐SCE exhibits an ionic conductivity of 2.5 × 10−4 S cm−1 at room temperature, higher than the Li3PS4‐SCE (1.75 × 10−4 S cm−1). Moreover, Li7PS6‐SCE displays better electrochemical cycling performance in solid‐state Li metal batteries with LiNi1/3Mn1/3Co1/3O2 (NMC 111) cathode.. When increasing upper cut‐off voltages from 4.0 to 4.4 V, Li| Li7PS6‐SCE |NMC111 cells deliver higher discharge capacities but exhibit worse cycling stability. Interface analysis using X‐ray photoelectron spectroscopy (XPS) reveals the formation of LiF under a high voltage of 4.4 V, while t not present with 4.0 V. This work explores the synthesis of SCEs with different sulfides in a strong polar solvent and highlights the interface reactions between sulfide/PVDF‐HFP SCEs with oxide cathodes.

The Research of PVC Sulfide Cathode Material

Pvc Disulfide As Cathode Materials for Secondary Lithium Batteries

Cathode Materials: Phosphorous Pentasulfide as a Novel Additive for High-Performance Lithium-Sulfur Batteries (Adv. Funct. Mater. 8/2013)

Cathode Materials: Phosphorous Pentasulfide As a Novel Additive for High‐Performance Lithium‐Sulfur Batteries (adv. Funct. Mater. 8/2013)

Polyisoprene Captured Sulfur Nanocomposite Materials for High-Areal-Capacity Lithium Sulfur Battery

Long-chain Solid Organic Polysulfide Cathode for High-Capacity Secondary Lithium Batteries

Anion Intercalation of VS 4 Triggers Atomic Sulfur Transfer to Organic Disulfide in Rechargeable Lithium Battery

Synthesis Of A New Inorganic Polymer Cathode Cyclic Phosphazene Trisulfide

Research Progress in Sulfur-Rich Polymers Cathode Materials for Li-ion Batteries

Interface Stability of Sulfide/PVDF‐HFP Solid Composite Electrolyte with High Voltage NMC Cathode

Sulfurization of Polymers with Elemental Sulfur As Cathode Materials for Rechargeable Lithium Batteries

Analysis of the synthesis process of sulphur-poly(acrylonitrile)-based cathode materials for lithium batteries

Quantitative Investigation of Polysulfide Adsorption Capability of Candidate Materials for Li-S Batteries

Softening and Enriching Polarity of Chitosan Backbone as a Bifunctional Binder for High-performance Sulfur Cathode

Sulfur-containing polymer/carbon nanotube composite cathode materials for high-energy lithium–sulfur batteries

Sulfur Distribution Analysis in Lithium−Sulfur Cathode via Confined Inverse Vulcanization in Carbon Frameworks

The Preparation and Characterization of Poly (phosphazene Trifulfide) As an Inorganic Polymer Cathode Material

Water-Soluble Trifunctional Binder for Sulfur Cathodes for Lithium–Sulfur Battery

Kinetic investigation of sulfurized polyacrylonitrile cathode material by electrochemical impedance spectroscopy

Improving the room/low-temperature performance of VS<sub>4</sub> anode by regulating the sulfur vacancy and microstructure

In-situ crosslinked binder for high-stability S cathodes with greatly enhanced conduction and polysulfides anchoring