Abstract:This paper describes the conceptual design and aerothermal approach of the ABB ALSTOM POWER UK Limited (ABB ALSTOM POWER) dry low emission (DLE) combustion system directed towards all current and future power ranges. A set of parameters was employed as a common criterion to design the company's combustion system across the product range. The parameters made it possible to scale the combustion system to operate at any required firing temperature without the penalty of achieving the low emission targets. The logic and sensible air mass mapping and testing management based on a basic knowledge of the aerothermodynamics of the combustion system and its integral parts produced reliable operation and engine results. The combustion system aerothermodynamic design considers the constraints of maintaining combustor specifications while introducing a reliable ultra-low NO x concept with minimal structural change to engine design. Furthermore, the ignition loop, piloting and stability margins were issues continuously assessed through a defined application programme to examine their impact on engine operability at various load conditions. A main radial swirler injector is utilized for both gas and liquid to produce a fuel lean mixture for combustion at full-load operating conditions, while a pilot fuel injector guarantees a local fuel-rich zone to sustain stability at low power conditions. The carefully planned switch-over between the pilot and main swirler provides smooth operation and low emission across the load range conditions. The company combustion system relies upon the principle of aerodynamic variable mixing with a single vortex generator burner. The partial premixing process takes place at the radial inflow swirler slots before the fuel—air mixture is introduced into a prechamber and thereafter into the combustion chamber. For vane passage injection the liquid liquid fuel atomization should be at an optimum and the vane passage and prechamber length set to provide the vaporization period. The impingement cooling scheme aided by a thin layer of thermal barrier coating (TBC) achieved an excellent combustor wall temperature at all operating conditions and across the DLE engines product range. The scheme made it possible to direct a large amount of air towards the swirler to achieve the lean premix combustion. Substantial CO emission reduction at part load was achieved by variable guide vanes (VGV) modulation for the single-shaft engines. This action inhibits NO formation without slowing the CO oxidation process to a frozen condition. The variable mixing regime approach and accurate air management has demonstrated an ultra-low NO x emission of 12–15 and 32–35 ppmv (corrected to 15% O 2 ) at the full-load condition while operating on gas and distillate-2 fuel respectively. Moreover, the system exhibited low CO and dynamics oscillation capability for both gas and liquid fuel operation. At the present time, the one-dimensional analysis has been proved to be a reliable tool for combustion system designers to produce a preliminary design configuration. The particular choice for a commercial computational fluid dynamics (CFD) code to satisfy various criteria of the swirling combusting flow is proving to be difficult due to constraints regarding slover and/or methods limitation. The results obtained from the high-pressure air facilities, engine beds and field trials represent a true technological achievement through collective engineering design efforts towards emission and pollution control for small- and medium-range gas turbine engines.

A Combustion Reference Temperature Estimation Algorithm of Gas Turbines

Access to Empirical Formulations of Combustion Efficiency for Gas Turbine Combustors with Improved Generalization Ability

A Comparative Study on Fault Detection Methods for Gas Turbine Combustion Systems

Unit Load and Combustion Control Optimization Based on Radiation Energy Signals

Coordinated Optimization Control of Flue Gas Temperature for Improving Reaction Efficiency of Catalyst

Experimental and Numerical Investigation of the Non-Reacting Flow in a High-Fidelity Heavy-Duty Gas Turbine DLN Combustor

An Analysis of the Methods for Estimating the Dry Low NOx Pollutant Emissions from a Combustor

Optimization of Annular Combustion Zone for Heavy Duty Gas Turbine DLN Combustor

Design methods of the ABB Alstom Power gas turbine dry low emission combustion system

Analysis and Deliberation upon Combustor Technology Development for the G/H Class Gas Turbine

Influence of the turbulence model on the numerical predictions of cold turbulent flow in a heavy-duty gas turbine DLN combustor

Performance Test Of Dln Combustor For 110 Mw Heavy-Duty Gas Turbine

A Bayesian Optimization Framework for the Control of Combustion Instability of a Bluff-Body Stabilized Combustor

Gas turbine circumferential temperature distribution model for the combustion system fault detection

Combustion Tuning for a Gas Turbine Power Plant Using Data-Driven and Machine Learning Approach

Numerical Simulation of Three-Dimensional Combustion Flow in a Gas Turbine Annular Combustor

Method for Determining the Change in Gas Turbine Firing Temperature

The Cooling Air Estimation of Large Scale Gas Turbine

Lessons Learned Toward Estimating the High-Pressure Turbine Inlet Temperature Profile Using Measurements Acquired at the High-Pressure Turbine Exit

Study on Calculation of Theoretical Combustion Temperature of BF

Study on the Flame Transition Characteristics of a Gas Turbine Combustor