Analysis of Flash-boiling Spray Mechanism using a Two-Dimensional Transparent Nozzle
Shengqi Wu,Min Xu,Yuyin Zhang,Gaoming Zhang,Lei Li
2013-01-01
Abstract:To meet the more stringent emission regulations, a desirable spray structure could be very useful to improve the combustion efficiency of spark-ignition direct-injection (SIDI) engines. For example, sprays with enhanced atomization and faster vaporization are beneficial for reducing the emission of unburned hydrocarbon and soot particles. Recent results reveal that flash-boiling spray possess these desirable characteristics with shorter penetration, wider spray angle, faster evaporation, and smaller drop sizes. All these characteristics can be achieved when heated fuel is injected into an ambient environment below its saturation pressure. Compared with the conventional sprays of high pressure injection systems, flash-boiling spray is much easier to achieve without the need of expensive pressure-based injection system. In this study, a two-dimensional transparent nozzle was constructed to reveal the microscopic flow inside the nozzle channel. Using high-speed microscopic backlit and Schlieren imaging techniques, flow characteristics of both inside and outside of the two-dimensional transparent nozzle were investigated. The flow characteristics inside the nozzle and their influence on the liquid jet formation under superheated conditions were examined. It was found that the mechanisms leading to the formation of flashboiling spray could be better revealed. *Corresponding author: mxu@sjtu.edu.cn Introduction The great potential to improve vehicles’ fuel economy with low cold start emission is the main reason for the wide adoption of spark-ignition directinjection (SIDI) engines around the world [1]. In SIDI engines, fuel is directly injected into the combustion chamber. It mixes with intake air under the forces induced by fuel injection and moving piston. However, high level soot and unburned hydrocarbon emissions would be generated because of the existing fuel-rich region and harsh combustion conditions [1, 2]. Thus, various measures should be taken to optimize the combustion system in order to achieve higher fuel efficiency and lower soot emissions. In view of this, an ability to produce an idealized spray for SIDI engines is of great interests. As a traditional solution, high pressure injection systems are popular ways to improve the fuel spray quality by enhancing the fuel atomization and evaporation. In doing so, more homogenous combustible mixture in the chamber can be obtained [3]. In addition, with the recent deployment of multihole fuel injectors, flexible spray patterns can be easily changed by adjusting the hole configuration such as the hole angle and length-to-diameter (L/D) ratio. However, high injection pressure system also generates negative issues. For example, an overpenetrating spray would lead to fuel impingement and abnormal combustion [4-6]. In addition, it would be very difficult to continue raising the injection pressure of the fuel system when it already reaches a very high level. Thus the cost and efficiency of high injection system become unacceptable [7]. It has been well documented that changing the fuel temperature is also an effective way to increase the evaporation and atomization process of the liquid fuel, especially when the fuel becomes superheated as soon as it is injected into the condition that the ambient pressure is below its saturation pressure. This phenomenon is called flash boiling [8-10]. Flash boiling spray was first discovered by Brown et al. in 1960s and they provided an initial description of the atomization process [11, 12]. Later, Plesset and Zwick established the most widely accepted mechanism of the bubble generation and evolution in the flash boiling spray [13]. The application of flash boiling spray was studied to promote combustion and reduce emission in a diesel engine [14]. In addition, Senda et al. proposed the idea to improve the fuel-air mixture in the chamber through flash boiling spray [15]. Both macroscopic and inner spray structures have been investigated via various optical diagnostics. It was found that the flash boiling spray structure was dominated mainly by the superheated degree of the injection condition [10]. Specifically, the droplet size distribution was measured using an improved laser sheet drop sizing (LSD) method developed by Zeng et al. [16]. The laser induced exciplex fluorescence (LIEF) technique was employed to obtain both qualitative and quantitative analysis of the evaporation process of flash boiling spray [17, 18]. Zhang et al. [19, 20] studied the collapsing structure of spray using high speed particle image velocimetry. All research results point to the fact that flash boiling sprays possess smaller drop size, wider spray angle and shorter spray penetration than conventional liquid sprays. These features contribute to the accelerated vaporization process and homogenous distribution [10]. In addition, other factors such as fuel properties, fuel temperature and ambient pressure also play a vital role in the formation of flash boiling sprays [8, 10]. A systematical summary has been reported by Xu et al. recently [21]. It is obvious that a flash boiling spray possesses very different spray characteristics in that the mechanism involved in the flash boiling spray must be different from the conventional liquid sprays. Thus, the observations of droplet break-up and evaporation process of liquid sprays are no longer applicable to the flash boiling spray. Higher fuel temperature leads to thermodynamic instability of fuel which would contribute to a large amount of bubbles generated inside the nozzles. It has been shown that bubble break-up would accelerate the atomization and evaporation process [22]. Although external spray characteristics could be coupled together for the analysis of the atomization and evaporation mechanisms, it is still not enough to acquire an accurate understanding. However, the inner flow characteristic of the nozzles is extremely essential, which would give abundant information to reveal the flash boiling spray. Although some work has been done to investigate the internal flow of the injector, most of which were focused on the cavitation phenomenon inside the nozzle under non-flash boiling conditions. It has been pointed out that cavitation takes place in the nozzle of pressure atomizers [23, 24], and influences the spray structure, the magnitude of which can be identified according to the cavitation number [22]. Arcoumanis et al. identified the geometrically-induced cavitation and string cavitation, and discovered the initiate places of cavitation [25]. However, most of the experiments were conducted at fixed temperatures and using one specific fuel. Little work has been done to reveal the flow inside the nozzle especially on flash boiling conditions. Bubble generation mechanism and evolution process are both not clear at all. In the present study, three kinds of fuel, namely, npentane, iso-octane and winter blend gasoline were tested employing a 2-D transparent nozzle under various flash boiling conditions. Combining the flash boiling spray results and the flow characteristics inside the two-dimensional transparent nozzle, the mechanism of flash boiling sprays could be better understood. Experimental Techniques and Apparatus Figure 1 shows the schematic of the experimental apparatus, including a quiescent high pressure chamber, an ambient pressure control system, a fuel supply system and a specific optical diagnostic system according to different testing objectives. The quiescent high pressure chamber can be operated under the back pressure between 10 kPa and 2 MPa at atmospheric temperature, and can be used for diverse optical access by changing the test section in the middle part. The chamber was connected to a high pressure nitrogen cylinder and also a vacuum pump, which was used for high ambient pressure and vacuum control respectively to simulate the injection condition of a SIDI engine. The fuel supply system contained a pressure control system and a fuel temperature control system. A hydraulic piston accumulator was used to pressurize the fuel to reach the injection pressure target and maintain the pressure during the test. A water jacket was designed in the injector fixture, connected to a heat exchanger, to cool or heat the fuel ranging from -20 o C and 90 o C. In addition, a heat tape was used to wrap around the clamps for thermal regulation. It was controlled by a PID controller to ensure even temperature distribution surrounding the fixture. For the imaging diagnostic system, a programmable timing unit (PTU), developed by LaVision, was used to synchronize the light source, injection system and image acquisition system. A high speed microscopic imaging system was built in which a high speed camera equipped with a long distance microscope and a xenon light were employed to acquire magnified images of the flow under different flashboiling conditions. Likewise, the same high speed camera and xenon light were also used in a Z-type Schlieren system to image the jet exiting at the near field of the nozzle, as depicted in Figure 2. A pair of plane mirrors guarantees the high sensitivity in a small operation area. Other auxiliary systems including fuel supply system, ambient pressure control system and data acquisition system are the same as described before. Figure 1. Experimental setup for internal flow characterization Parabolic Mirror Parabolic Mirror Plane Mirror Plane Mirror